Wall & Facade Systems
Vetotouch MARMO

Marble chip decorative exterior and interior finishing system

Uses
Marble chip finish designed for interior/exterior application.
On plastered, fairfaced concrete surfaces.
On block walls and pre-cast panels.
5-15 mm thickness.
Fast Download
Technical Data Sheet
download (*.pdf 0.21Mb)
Catalogues
Decorative Coating Brochure
download (*.pdf 2.78Mb)
External Thermal Insulation Composite System - ETICS
download (*.pdf 8.19Mb)
Technical Information
Product Description

Vetotouch Marmo is a cement based decorative finish composed of hydraulic binders, selected aggregates and special additives . It is supplied as a dry powder in a pre-weighed bags ready to use on site, which requires only addition of clean water to produce easily workable mortar. 

Advantages
  • Factory controlled pre-blend ensures consistent high quality
  • Requires only addition of water on –site at the time of usage.
  • Provides a variety of finishes using various colors and marble chip types..
  • Improved workability and curing
  • Easy application with uniform work flow enables high productivity and superior finishing.
  • Strong adhesion on variety of substrates.
  • Internal and external applications.
  • Weather resistant.
  • UV stable pigment provides resistance to fading and eliminates need for additional paint
  • Suitable for humid and dry condition.
Compiliance Standard
  • EN 998:2010
    EN 926:2011
    EN 13914:2005
    EN 1015:2000
Packaging & Coverage

Vetotouch Marmo supplied in 25 Kg Bag
Coverage - 1.9 Kg / m2 / 1 mm Thickness

Colors
Saveto Standard Colors
Application Information
Instructions for use

Mixing

Add to the mixing container 5-5.5 liters of water for each 25 kg bag of Vetotouch Marmo. Add the powder to the water and mix with a mechanical plaster mixer or low speed heavy duty electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump free consistency is achieved. Leave the mixed material to stand for 10 min and briefly remix without addition of water.

Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when homogeneous mix is achieved.
Add 0.5 to 1.0 liter of Vetobond AB432 to the mixing water and adjust the water requirement accordingly for each 25 kg adjust the water requirement accordingly for each 25 kg bag. Follow same mixing procedure as described above.
Mixed material must be used within 2 hours.
Do not add water, once the mixed mortar start to harden.

Application
Vetotouch Marmo can be applied in a single layer (5 - 15 mm) or multiple layers up to 25mm on rough or smooth surfaces to desired thickness. For multiple layers application, each layer should not exceed 15 mm.
For second layer allow the plaster to partially set (60 – 120 min depending on weather). Apply second layer as described above to desired total thickness not exceeding 25 mm.
Apply design scheme and joints using the colors required using a small amount of the mixture at a thickness of 2 mm to glue the plastic spacers, use the processed plastic spacers with the required lengths, and allow for a period of not less than 10 minutes to dry. Broadcast the wet surface mixture with marble chips and when the mixture begins to stiffen compress the chips into the surface with a steel or plastic trowel to have homogeneous level with attractive design.
Apply a coat of Vetoseal XX772 for protection against water penetration, chloride ion attack, freeze/thaw cycles, weathering and airborne contaminants.

Curing
Vetotouch Marmo is best cured by spraying an acrylic based curing compound on the surfaces of applied materials.

Additional Information
Health & Sefety

Original sealed bags of Vetotouch Marmo has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Cool Plaster

Advanced Modified Cementitious Thermal Insulating Plaster

Vetotherm FLEX

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm ULTRA

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm Plaster

Advanced Modified Cementitious Thermal Insulating Plaster

Vetotouch EUROPA

Cementitious polymer modified decorative finish coat applied at thicknesses from 1 to 5 mm

view more
Featured Product
Vetorep ER352

Twin Pack Putty “Formulated for Thick Vertical and Overhead Applications“ 

Uses
Repair of concrete surface pores, blemishes at thickness from feather edge.
Sealing of surface cracks in aggressive environments and in injection repairs.
Leveling of surface imperfections and irregularities prior to application of Saveto resinous coatings and toppings range.
Fixing and bedding of tiles, dowels and anchors.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map