Wall & Facade Systems
Vetotouch TEXTURA

Acrylic polymer modified decorative finish coat applied at thicknesses from 3 to 20 mm

Uses
External and internal building facades.
As a finish coat for of EIFS / ETICS systems.
Block walls and concrete surfaces.
On scratch coated overhead surfaces.
Fast Download
Technical Data Sheet
download (*.pdf 0.23Mb)
Catalogues
Decorative Coating Brochure
download (*.pdf 2.78Mb)
External Thermal Insulation Composite System - ETICS
download (*.pdf 8.19Mb)
Technical Information
Product Description

Vetotouch Textura is an acrylic polymer modified cement based render coat composed of hydraulic binders, selected aggregates special pigments and high performance additives. It is supplied as a dry powder in pre-weighted bags ready to use on site, which requirs only addition of clean water to produce cohesive mortar. Vetotouch Textura is a high quality product and suitable for external applications. Vetotouch Textura is available in white and vetonit standard colors and custom colors with minimum order restrictions.

Advantages
  • Factory controlled pre-blend ensures consistent high quality
  • Requires only addition of water on –site at the time of usage.
  • Uniform color / mass.
  • Improved workability and curing
  • Easy application with uniform work flow enables high productivity and superior finishing.
  • Strong adhesion on variety of substrates.
  • Internal and external applications.
  • Weather resistant.
  • UV stable pigment provides resistance to fading and eliminates need for additional paint
  • Suitable for humid and dry condition.
Compiliance Standard
  • EN 998:2010
  • EN 926:2011
  • EN 13914:2005
  • EN 1015:2000
Packaging & Coverage

Vetotouch Textura supplied in 50 Kg Bag
Coverage - 1.4 - 1.6 Kg /m2 / mm Thickness

Shelf Life & Storage

Original sealed bags of Vetotouch Textura has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Colors
Vetotouch Textura is available in white and vetonit standard colors and custom colors with minimum order restrictions.
Application Information
Instructions for use

Mixing

or manual application add to the mixing container 14 liters of water for each 50 kg bag of Vetotouch Textura or 16 liters / 50 kg bag for machine application. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump free consistency is achieved.
Leave the mixed material to stand for 10 min and briefly remix without addition of water.
Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when homogeneous mix is achieved.

Smooth Concrete Surface
Add 1.5 to 2.0 liter of Vetobond AB432 to the mixing water and adjust the water requirement accordingly for each 50 kg adjust the water requirement accordingly for each 50 kg bag. Follow same mixing procedure as described above.
Mixed material must be used within 1 hours.
Do not add water, once the mixed mortar start to harden.

Application
Vetotouch Textura can be applied in a single or two coats on smooth surfaces by trowel application to achieved desired thickness 3-20 mm. Where spray applications are required kindly use Vetotop CP-S.
Apply mixed material using spray machine or hawk and trowel technique. Rod or screed to uniform thickness, not exceeding 20 mm for single coat or 10 mm each coat for multiple layers. First layer should be pressed hard against the surface.
For second layer allow the plaster or partially set (60-120 min depending on weather). Apply second layer as described above.
Water spray the surface if second layer is carried out next day.

Curing
Vetotouch Textura is best cured by spraying an acrylic based curing compound on the surfaces of applied materials.
During hot and dry conditions allow curing for minimum of 5 days. It will help to obtain high physical properties.

Additional Information
Health & Sefety

Vetotouch Textura is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.

Vetotouch Textura is non-flammable. For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Cool Plaster

Advanced Modified Cementitious Thermal Insulating Plaster

Vetotherm FLEX

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm ULTRA

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm Plaster

Advanced Modified Cementitious Thermal Insulating Plaster

Vetotouch EUROPA

Cementitious polymer modified decorative finish coat applied at thicknesses from 1 to 5 mm

view more
Featured Product
Vetotouch Brillante

Exterior decorative textured render

Uses
Ideal for application to most building where a simulated stone effect finish is required.
As a finish coat for of EIFS / ETICS systems
On plastered, fair faced concrete surfaces.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map