Tile Adhesives and Grouts
Vetoset CA544

Specialty polymer modified cementitious adhesive for glass blocks and glass mosaic tiles.

Uses
As an adhesive for glass block.
As an adhesive for glass mosaic tiles.
Bed and gap thickness of 5 to 10 mm.
Internal and external applications.
Fast Download
Technical Information
Product Description

Vetoset CA544 is a special mortar composed of high performance hydraulic binders, synthetic resins, carefully selected fillers and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site which only require the addition of clean water to produce a creamy paste with thixotropic properties. Vetoset CA544 is specially formulated for sealing glass blocks and installation of glass tiles. Vetoset CA544 does not contain asbestos fibre or other toxic materials.

Advantages
  • Single component, it requires only addition of water, easy to mix & apply.

  • Excellent physical & mechanical properties. 

  • Water resistant. 

  • Extended open time, adjustability time, making installation easier. 

  • Excellent resistance to yellowing.

  • Suitable for interior & exterior applications. 

  • Excellent resistance to staining.

Compiliance Standard
  • BS:EN 12004 as type C2TE S1.

  • ISO 13007 as type C2TE S1.

  • ASTM C348 & C349

     

Packaging & Coverage

Vetoset CA544 is supplied in 20kg Bags, Yield: 16 Liters

Shelf Life & Storage

Original sealed container of Vetoset CA544 has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Colors
White Powder
Application Information
Instructions for use

Mixing

For the preparation of mortar adhesive, pour into a container 5.6- 6.4 liters of water for each 20 Kg bag of Vetoset CA544. Add the powder to the water and mix with a low speed electric drill fitted with a suitable paddle for 4-5 minutes, until a uniform, lump-free consistency is achieved. Allow the mixed material to stand for about 10 minutes and remix briefly with no further water to be added. 

It can also be blended manually for small quantity but ensure correct amount of powder to water is maintained. 

Mixed material can be used within 60 minutes at 25 degrees C. 

Do not try to remix or add water to the mixture once the mortar adhesive starts to harden. If the material starts to harden.

Application

Apply Vetoset CA544 with a trowel, then position the glass blocks in the opening. Use special molder to verify the glass block alignment. Remove the excess of mortar before it hardens. 

For Gap filling, compact the product using a smooth rubber spatula. Let the product harden for about 10 minutes, after that clean the surface using a damp sponge. When the product is well hardened, clean it with a dry rag. 

Cleaning

Tools and equipment can be cleaned with water immediately after use. Hardened materials will require removal by mechanical means.

Surface Preparation

The surface should be sound, clean free from loose material etc. Horizontal surfaces must be leveled and vertical sides should be perfectly plumb-in or secured in order to guarantee a perfect alignment of glass blocks. The support must be solid, compact, free from loose parts, dust and greasy substances. 

 

Additional Information
Health & Sefety

Vetoset CA544 is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.

Vetoset CA544 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

 

More Products from this section
Ceramic TILE FIX

Weather resistant cementitious adhesive for ceramic tiles.

 

Pool FIX

Polymer modified water resistant adhesive for fixing swimming pools, fountains & watertanks tiles.

 

Pool GROUT

Water resistant grout for swimming pool tile joints.

 

Porcelain TILE FIX

Polymer modified weather resistant adhesive for porcelain tiles.

 

PREMIUM PROJECT FIX

High quality ceramic tile adhesive for projects.

 

view more
Featured Product
Vetoprime UP360

Penetrating Moisture Cure Poly-urethane Primer

Uses
Penetrating primer for interior and exterior floor coatings
As a dust proofer for cementitious surfaces.
Sealing of semi-porous cementitious substrates.
Priming of joint edges to receive urethane, epoxy, and polyurea based sealants.
Priming of concrete slabs and walls to receive solvent free epoxy, urethane, MMA, polyurea and hybrid coatings.
Priming of concrete substrates to receive epoxy and urethane based repair mortars.
Priming of cementitious screeds to receive epoxy, urethane and resinous toppings.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map