Wall & Facade Systems
Vetotouch Repara

Dual component cementitious coating and color nuetralizer for cementitious decorative finishes

Uses
Water absorption reduction and resistance to atmospheric contaminants.
As a color uniforming coat for the Vetotouch product range..
Patch cosmetic repairs of thin cementitious finishes.
Colored coating for fair-faced concrete providing carbonation resistance while being breathable.
Fast Download
Technical Data Sheet
download (*.pdf 0.17Mb)
Technical Information
Product Description

Vetotouch Repara is an acrylic polymer modified cement based colored coating composed of hydraulic binders, selected fine filler special pigments and high performance additives. It is supplied as a dry powder in pre-weighted bags coupled with modified acrylic enhancer ready to use on site, which only requires site mixing to produce cohesive coating. Vetotouch Repara is a high quality product and suitable for external applications. 

Advantages
  • Counteracts and minimizes effloresence phenomena.
  • Provides anti-carbonation properties.
  • Flexible providing crack bridging properties.
  • Non-Staining.
  • Ready pre-weighed components.
  • Uniform color / mass.
  • Improved workability.
  • Does not require curing.
  • Strong adhesion on variety of substrates.
  • Internal and external applications.
  • Weather resistant.
  • UV stable pigment provides resistance to fading and eliminates need for additional paint
Compiliance Standard
  • EN 998:2010
  • EN 926:2011
  • EN 13914:2005
Packaging & Coverage

Vetotouch  Repara is supplied in 15kg bag & 17 Liters Container, Yield: 21 Liters/ kit

Shelf Life & Storage

Original sealed bags of Vetotouch Repara has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Colors
Saveto Standard Colors
Application Information
Instructions for use

Mixing
Use a mobile mixer fitted with a saveto approved mixing paddel to stirr the liquid component for 1 minute prior to adding one third of its contents to the mixing vessle. The mixer should be of able to provide a variable speed between 300 and 500 rpm.
Once 1/3 rd of the liquid component have been added to the mixing vessel, start adding the powder component while continuing mixing. Once all the powder have been added, pour the remaining 2/3 of liquid component to the mix gradually and continue mixing for an additional 3 minutes

Application
Vetotouch Repara can be applied in a single or two coats on prepared surfaces using a stiff brush or a roller. Spray application can be facilitated by using spray gun.
Ensure complete and uniform coverage of the substrate with a minimum rate of 0.7 liters per meter squared.

Curing
Vetotouch Repara is self curing and does not require any additional measures. Allow to cure for 4 hours prior to applicaiton of any additional sealer coats.

Surface Preparation

For best results it is recomended to use water jets to wash surfaces that will receive the cementitious coating. In the case of grease contamination, a suitable chemical degreaser needs to be used to reach a clean cementitious substrate.
Once the surface has been cleaned, allow to dry naturally for a minimum of 2 hours.

Additional Information
Health & Sefety

Vetotouch Repara is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.
Vetotouch Repara is non-flammable.
For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Cool Plaster

Advanced Modified Cementitious Thermal Insulating Plaster

Vetotherm FLEX

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm ULTRA

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm Plaster

Advanced Modified Cementitious Thermal Insulating Plaster

Vetotouch EUROPA

Cementitious polymer modified decorative finish coat applied at thicknesses from 1 to 5 mm

view more
Featured Product
Vetoproof CR747

Rapid setting cementitious water plugging mortar

Uses
Temporary patching and stop flowing water from concrete and masonry segments
Emergency water stopping of service entry points in manholes or broken cementitious pipes at low pressure
Connected products
Vetotouch TYROLEAN

Exterior decorative textured render

Vetotouch TEXTURA

Acrylic polymer modified decorative finish coat applied at...

Vetotouch SERENE

Cementitious polymer modified decorative finish coat applied at...

Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map