High performance, aromatic waterproof polyurethane flooring membrane
Vetotop UC362 is a two component, solvent free aromatic polyurethane intermediate coat and waterproofing membrane. The product needs to be overcoated with Vetotop UC370 or Vetotop UC371 for optimum performance and scratch resistance. The products flexibility enables it to perform in a wide range of floowing applications including low service temperatures while maintaining flexibility and operational parameters.
Vetotop UC362 is supplied in 4 or 15 Liter Kits with coverage :1.25 m2 / Liter
Vetoprime UP360 is supplied in 4 Liter Kits with coverage: 8-10 m2 / Liter
Vetoprime EP390 is supplied in 4 Liter Kits with coverage: 8-10 m2 / Liter
Original sealed bag of Vetotop UC362 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.
Concrete substrates shall be primed with Vetoprime UP360 or Vetoprime EP390.
Mixing Vetotop UC362
In a separate mixing vessel, use a slow speed mixer to mix the base, hardener for 3 minutes. Mix these components in the quantities supplied taking care to ensure all containers are scraped clean. Do not add solvent thinners at any time.
Apply Vetotop UC362 by a pin leveler or airless spray to the surface. The application should be at a rate of 1.25 m2/litre per coat.
Application should not be carried out when relativehumidity exceeds 75%, or when the surface temperature to be coated is less than 3°C above the dew point.
Vetotop UC362 can be applied as a single coat, or dressed with Vetograin products to give a slip resistant finish.
For more information, please refere to Vetograin Technical Data Sheet.
Expansion joints in the existing substrate must be retained and continued through the Vetotop UC362 topping. Saveto have a range of joint sealants specifically designed for flooring (see Vetoflex PU781, and Vetoflex PS782 product data sheets).
Tools and equipment should be cleaned with Vetonit Solvent XX400 immediately after use.
The surface should be sound, clean, free from loose material, grease, laitence, dirt curing compound, etc. Laitence and weak surface layer shall be removed using mechanical methods such as grinding or blasting in order to provide a sound well profiled surface. All necessary repairs should be made prior to application by using epoxy mortar from Vetorep ER range. New concrete floors shall be at least 28 days old with moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).
Vetotop UC362 is irritant and harmful therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advise.
Ensure adequate ventilation when using product or when using solvent for cleaning purposes and avoid inhalation of vapours. The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medial advice. If swallowed, seek medical attention immediately - Do not induce vomiting.
Vetonit Solvent XX400 are flammable. Keep away from sources of ignition. No Smoking. In the event of fire extinguish with CO2 or foam. Refer to product(s) MSDS for further information.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
High performance, matt finish chemical, scratch & UV resistant polyurethane floor & wall coating
Premixed 2 to 10 mm thick cementitious self leveling underlayment
Premixed 30 to 100 mm thick cementitious screed.
Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating
Solvent based high performance, self priming, thin epoxy topping
Water based concrete curing compound