Concrete Grouts Repair and Enhancement
Vetoanchor EG346

Epoxy resin twin cartridge anchoring grout

Uses
Anchoring bolts, brick work, threaded Studs, hollow masonry sleeves, threaded inserts and steel columns into rock, concrete, masonry.
Permanent installation of reinforcement starter bars, foundation bolts, base plates, balustrading, barriers and safety fences, railway tracks, tie-back anchors, reinforcement doweling abutments, ground anchors for towers, cranes, dock sills etc
Fast Download
Technical Data Sheet
download (*.pdf 0.31Mb)
Method of Statement
download (*.pdf 0.58Mb)
Technical Information
Product Description

Vetoanchor EG346 is a two-component, styrene free, pure epoxy based, high strength adhesive anchoring system. The system includes injection adhesive in plastic cartridges, mixing nozzles, dispensing tools and hole cleaning equipment. The product is designed for bonding threaded rod and reinforcing bar hardware into drilled holes in concrete base and solid masonry materials. Vetoanchor EG346 is available in two packaging twin cartridge system: 400 milliliter that are side by side cartridges requiring a specifically designed injection gun.

Advantages
  • High grip force, high adhesive force.
  • Designed for use with threaded rod and reinforcing bar hardware elements.
  • Special application to diamond drilled holes and large bore diameter.
  • The product ingredients are odorless and non-toxic.
  • Orange color can be easily detected or monitored.
  • Wide application temperature range (0 - 40 ºC)
  • Styrene free.
  • Rapid strength gain.
  • Cost effective.
  • Excellent physical and mechanical properties.
Packaging & Coverage

Vetoanchor EG346  is supplied in 400 ml twin cartridge sets

 

Shelf Life & Storage

Original sealed kits of Vetoanchor EG346 has a shelf life of 18 months provided it is stored clear of ground in a dry and shaded temperature controlled place <35ºC.

Colors
orange
Application Information
Instructions for use

Design Criteria

The high strength of the cured resin permits strong anchors to be created. Ultimate strength is varied by:
- Strength of host material.
- Length of resin bond to bar.
- Hole preparation and formation.
- Type and dimension of bar.
Refer to Vetoanchor EG346 for more details and information.

Application
Oper the cartridge and remove the red stopper on top. Use Good Use nozzles after remove red stopper from the cartridge and attach the mixing nozzles screwing down tightly. Assemble cartridge into the caulking gun and dispense 2-3 trigger pulls of adhesive to waste until color is red with no streaks.
Open the valve and squeeze the handle so the material is dispensed out of the nozzle until an even, uniform orange color is anchieved. Before a new cartridge is introduced into the hole, dispense the first 10 ml or so to waste until mix is even on color (Orange) as well. Because initial flow should be disposed of into empty packaging or similar materials. Inject resin into hole, starting from the bottom of hole. The material must be injected without creating air pockets.
Insert studs or anchors, push the stud into the hole using a slow twisting motion. Wipe away the excess material. Anchor or stud need to be clean and oil-free. Do not touch studs or anchor until mixture has gelled and do not load the anchor until curing is complete as per curing time table.

Surface Preparation

Hole preparation
Optimum performance of Vetoanchor EG346 grouts requires rough sided, dust free holes. Use of rotary percussive drills with air pressure is recommended.
Diamond drilled holes should be under-reamed.
Cast holes should preferably be inverse dovetail configuration. If parallel-sided holes are cast they should be rough to provide adequate keying.
Brushing the holes and air blowing is a must for all holes, the concrete needs to be dry with relative humidity of less than 75% prior to application.

Limitation
  • Do not install anchors when substrate temperature is less than 0°C.
  • Do not install anchors when Vetoanchor EG346 temperature is less than 15°C.
  • AT temperatures below 15°C the product should be warmed or stored in temperatures of 15-30°C for 24 hours prior to use to improve product flow and cure.
  • If the gelling time is superceeded, use a new static mixer.
  • Do not cut or shorten nozzles.
  • If the cartridge is not finished, clean the opening, then put the plug back and cap tightly. The cartridge set can be used again in by replacing the static mixer.
  • Do not dilute the material with any solvents and/or other chemicals.
  • Not suitable for use in diamond cored holes without roughening.
  • Please ensure spiral mixer in nozzles.
  • Do not install into uncured concrete.
  • Please use Good Use nozzles, other nozzles may cause ineffective mixing and adversily affect the material.
Additional Information
Health & Sefety

Contact with the skin should be avoided as certain sensitive skins may be affected by contact with the epoxy resin. In such cases if contact with the resin occurs, the skin should be washed immediately with soap and water - not solvent. Gloves and barrier creams should be used when handling these products. Eye contamination must be immediately washed with plenty of water and medical treatment sought.
Vetoanchor PG346 is not Flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor PG347

Polyester injection and anchoring grout

Vetocure XT425

Water based concrete curing compound

Vetocure XT426

Multi-Purpose Acrylic Resin Curing Compound

Vetocure XT427

Water based acrylic curing compound and primer *

Vetogrout CG510

Multipurpose universal cementitious non-shrink grout

view more
Featured Product
Vetotop EC498

Solvent free high performance, high build epoxy flooring system

Uses
Floor coating for a variety of industrial applications such as: production assembly areas, workshops, dairies, bottling plants, breweries, pharma plants, kitchens, showrooms, etc.
Aircraft hangers, anti-slip floors, ramps & high traffic.
Wet working areas subject to chemical spillage.
Vehicle production factories and parks.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map