Water based acrylic curing compound and primer *
Vetocure XT427 I=is supplied in 20 Pail & 200 liter Drum, Coverage: 4 - 6 m2/Liter
Stated consumptions data are for general guidance. Actual consumption depends on the nature of substrate, method of application and wastage.
Vetocure XT427 has a minimum shelf life of 12 months, provided the temperature is kept within the range of 5ºC to 35ºC. Freezing and prolonged exposure to heat or direct sunlight should be avoided. Should the temperature of the product fall outside this range then Saveto Technical Service Department should be contacted for advice.
Containers should be kept sealed and airtight to prevent loss of moisture by evaporation.
Application to fresh concret
Vetucure XT427 should be spray applied to the surface of fresh concrete. Application should be made approximately 30 minutes after evaporation has left the concrete free from surface water.
Spray machine producing a fine mist may be used for Vetocure XT427 application, such as knapsack or motorised sprayers. The suitability of the machine should be ensured by an application trial. The spray nozzle should be held approximately 450 mm from the concrete surface and passed back and forth to ensure complete coverage. Pump pressure should be maintained to give an even, fine spray.
To ensure continued curing, no further application of water or other material is necessary after application. The cured surface should not be disturbed until it has sufficient strength to bear surface loads. The applied film should not be waked on before it is fully dry and care should be taken to ensure that the film is not broken.
Application to hardened concrete
Vetucure XT427 can be applied manually if spray machine is not available. Use soft brush, broom or wide roller for applying Vetocure XT427. Application in this manner should only be made once the concrete has hardened sufficiently to not be damaged during application.
Vetocure XT427 may also be applied to the surface of newly hardened concrete immediately after de-moulding. The surface must be structurally sound, free from oil, grease and other forms of contamination. which may otherwise prevent adhesion of Vetocure XT247 to the concrete.
The recommended coverage rate for Vetocure XT427 is between 4.0 and 6.0 m2 / litrer (0.17 - 0.25 litres/m2 ).
Over-coating and removal
Vetocure XT427 can be applied over old, covered substrates. Small trial area is recommended to ensure that the desired properties are obtained.
Before over-coating with Vetocure XT427, ensure that the surface is completely free of stains, oils and other materials that may interfere with the adhesion of the material.
* Important Note
Consult your Saveto technical representative for conditions and application method.
Spray equipment should be cleaned immediately after use by flushing through with water.
Vetocure XT427 does not fall into the hazard classifications of current regulations. However, it should not be swallowed or allowed to come into contact with skin and eyes either in bulk or spray form.
Suitable protective gloves and goggles should be worn. Splashes on the skin should be removed with water. In case of contact with eyes rinse immediately with plenty of water and seek medical advice. If swallowed seek medical attention immediately - do not induce vomiting.
Vetocure XT427 is non - flammable.
For further information consult the Material Safety Data sheet available for this product.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Epoxy resin twin cartridge anchoring grout
Polyester injection and anchoring grout
Water based concrete curing compound
Multi-Purpose Acrylic Resin Curing Compound
Multipurpose universal cementitious non-shrink grout
Specialty polymer modified cementitious adhesive for glass blocks and glass mosaic tiles.