Flooring & Coatings Systems
Vetotop EC397

Slightly Elastic Solvent free Industrial-Grade high performance,high build epoxy flooring system

Floor coating for a variety of industrial applications such as: production assemblyareas, workshops, dairies, bottling plants, breweries, pharma plants, kitchens, showrooms, etc.
Aircraft hangers, anti-slip floors, ramps & high traffic.
Wet working areas subject to chemical spillage. u Vehicle production factories and parks.
Fast Download
Technical Data Sheet
download (*.pdf 0.14Mb)
Technical Information
Product Description

Vetotop EC397 is a two component high performance solvent free epoxy coating system that is especially designed for industrial flooring. Once cured, the product has excellent abrasion and chemical resistance. Vetotop EC397 provides an attractive hard wearing and easily cleanable floor finish. Its use on floors will enhance lighting in the environment due to the product reflective properties.

  1.    High abrasion and impact resistance. u   Ease of application.
  2.    High abrasion and chemical resistance. u   Low maintenance costs.
  3.    Hygienic, impervious and easily cleanable. u   Slip-resistant finish can be obtained.
  4.    Available in 8 standard colors with possibility of custom RAL colors.
  5.    High  bond,  stronger  than  concrete  cohesive strength.
  6.    Slightly flexible to handle vibration u   Economic installation.
Compiliance Standard

BS EN476:2009 as class 1 in flame spread.

Packaging & Coverage


Pack Size

Vetotop EC397

4 Liter Kits

Vetoprime EP390

4 Liter Kits

Vetotop UC371

4 & 15 Liter Kits

Antislip Aggregates

25 Kg Bags




Vetotop EC397

2 m2 / Liter @ 500 microns

Vetoprime EP390

8 m2 / Liter

Vetotop UC371

10 m2 / Liter

Shelf Life & Storage

Original sealed bag of Vetotop EC397 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.

Application Information
Instructions for use

Mixing Vetotop EC397

In a separate mixing vessel, use a slow speed mixer to mix the base, hardener for 3 minutes. Mix these components in the quantities supplied taking care to ensure all containers are scraped clean. Do not add solvent thinners at any time.



The first coat of Vetotop EC397 should be laid using a short haired lamb wool roller, or gauged squeegee to achieve a continuous coating. Ensure that loose hairs on the roller are removed before use. A minimum film thickness of 500 microns per coat should be applied for flooring system (this can be increased where specifications demand).

Vetotop EC397 should be topcoated with Vetotop UC371. The top coat can be applied in the same manner within 8 to 24 hours of the application of the top coat.


Antislip Aggregates

If the option of using antislip aggregates has been chosen, the base coat should be dressed with the chosen antislip aggregates as soon as possible after laying of the base coat. The recommended procedure is to completely blind the base coat i.e. apply excess dressing aggregate to completely obliterate the base coating.

Alternatively, the antislip silica particles can be broadcast in a light random dressing to provide a less dense finish, or the product can be used to obtain a smooth finish by omitting the antislip aggregates.

When the base coat has reached initial cure (after 12 hours at 20°C or 6 hours at 40°C), the excess aggregate should be vacuum cleaned from the surface.

The top coat can now be applied by a short haired roller or airless spray equipment. Care should be taken to ensure that a continuous film is achieved and the rough surface caused by the aggregate is completely sealed. This topcoat must be applied within 36 hours at 20°C (24 hours at 40°C) of the application of the resin base coat.


Expansion Joints

Expansion  joints  in  the  existing   substrate   must be retained and continued through the Vetotop EC397 topping. Saveto have a range of joint sealants specifically designed for flooring (see Vetoflex PS781, Vetoflex PS782 and Vetoflex PS786 product data sheets).



Tools and equipment should be cleaned with Vetonit Solvent XX400 immediately after use.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitence, dirt curing compound, etc.

Laitence and weak surface layer shall be removed using mechanical methods such as grinding or blasting in order to provide a sound well profiled surface. All necessary repairs should be made prior to application by using epoxy mortar from Vetorep ER range. 

New concrete floors shall be at least 28 days  old with moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).



Priming is not normally required provided the substrate is sound, prepared and good quality non porous concrete. However, if concrete surface is porous, or w/c ratio is >0.5 it is recommended to use Vetoprime EP390.

Vetoprime EP390 should be mixed in the proportions supplied. Add the entire contents of the hardener can to the base can. When thoroughly mixed, preferably using a slow speed mixer, the primer should be applied in a thin, continuous film using rollers or stiff brushes. Work the primer well into the surface of the concrete taking care to avoid ponding or over application. The primer should be left to achieve a tack-free

Additional Information
Health & Sefety

Vetotop EC397, Vetotop UC371, Vetoprime  EP390 and Vetonit Solvent XX400 should not come into contact with skin and eyes or be swallowed. Ensure adequate ventilation and avoid inhalation of vapors. Some people are sensitive to resins, hardeners and solvents. Wear suitable protective clothing, gloves, and eye protection. If working in confined areas, suitable respiratory protective equipment must be used.

The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medial advice. If swallowed, seek medical attention immediately - Do not induce vomiting.

Vetoprime EP390 and Vetonit Solvent XX400 are flammable. Keep away from sources of ignition. No Smoking. In the event of fire extinguish with CO2 or foam.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.


More Products from this section
Vetotop UC372

High performance, matt finish chemical, scratch & UV resistant polyurethane floor & wall coating

Vetotop CL530

Premixed 2 to 10 mm thick cementitious self leveling underlayment

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed.

Vetotop EC198

Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating

Vetotop EC493

Solvent based high performance, self priming, thin epoxy topping

view more
Featured Product
Vetotop EL392

Industrial grade self smoothening epoxy based floor topping from 0.8 to 2 mm thickness

Industrial kitchens and food processing plants
Heavy duty vehicle factories, car parks and aircraft hangers
Clean rooms, battery rooms and laboratories
Any flooring were impact resistance is of importance
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map