UAE
Bahrain Egypt Jordan Saudi Arabia
EN
EN
Contact news and events About us Home
PRODUCT RANGE
SYSTEM
Selector REFERENCES DOWNLOAD SECTION
Wall & Facade Systems
Cool Mortar

Advanced modified cementitious light weight, thermal insulating masonry mortar 

 

Uses
As a joint filler between light weigh and insulated blocks to obliterate thermal bridging phenomena resulting from use of normal mortars.
Between sandwich polystyrene blocks or AAC blocks
Fast Download
Technical Data Sheet
download (*.pdf 0.20Mb)
Technical Information
Product Description

Cool Mortar is a cement based mortar composed of hydraulic binders, selected aggregates, light weight particles and high performance additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce cohesive mortar. It is a premium quality product containing special adhesion additive. Cool Mortar will enable sandwich block to achieve the required U-value by eliminating thermal bridge phenomenon. The product provides thermal insulation for building wall sections relying on advanced material technologies. 

 

Advantages
  • Factory controlled pre-blend ensures consistent high quality. 
  • Requires only addition of water on-site at the time of usage.
  • Suitable for ME harsh weather conditions.
  • Easy application with uniform work flow enables high productivity & superior finishing. 
  • Strong bond in blocks & wall joints.
  • Internal & external applications.
  • Suitable for wet to dry conditions.
Compiliance Standard
  • BSEN 1015-11
  • BSEN 998-2 – Tabulated value initial shear strength
  • BSEN 1015-18
  • BSEN 1745 A.12
  • BSEN 1745 tabulated value A.12 @ P50%
Packaging & Coverage

Cool Mortar is supplied in 20 Kg Bag (23.5 Liters)

Coverage:

  • 29 L.M/ 10mm (Solid block 400x200x200 mm)
  • 39 L.M/ 10mm (Solid block 400x200x150 mm)
  • 59 L.M/ 10mm (Solid block 400x200x100 mm)
Shelf Life & Storage

Original sealed bags of Cool Mortar has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

 

Colors
Grey colour Powder
Application Information
Instructions for use

Mixing

Add to the mixing container 5.8 to 6.6 litres of water for each 20 Kg bag of Cool Mortar. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved. 

Leave the mixed material to stand for 10 min and briefly remix without addition of water.

Manual mixing is allowed for small batch quantities by mixing for approx. 1-2 min, or when homogenous mix is achieved. 

Application

Saturate the block surface with water before applying mortar. Any excess water should be removed.

Cool Mortar is spread with trowel on the surface and joints where the blocks are to be mounted.

Fill joint in similar way as conventional sand/cement mortar.

After stiffening, Cool Mortar should be given a final smoothing to remove protrusions and eliminates undulations.

Curing

Cool Mortar is a cementitious product and accordingly should be cured to recommended ACI and international curing practices. 

Cleaning

All tools should be cleaned immediately after finishing by water. Hardened materials can be cleaned mechanically.

Surface Preparation

The substrate should be sound, clean, free from loose material, grease, laitance, dirt, curing compound, etc. 

Prior to Cool Mortar application, wet the entire surfaces with clean potable water and surface  should look damp at the time of Cool Mortar application.

Additional Information
Health & Sefety

Cool Mortar is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.

Cool Mortar is non-flammable.

For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Cool Plaster

Advanced modified cementitious thermal insulating plaster

 

Vetotherm FLEX

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm ULTRA

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm Plaster

Advanced Modified Cementitious Thermal Insulating Plaster

Vetotouch EUROPA

Cementitious polymer modified decorative finish coat applied at thicknesses from 1 to 5 mm

view more
Featured Product
Vetotop US364

High performance solvent free polyurethane screed for heavy duty applications 

Uses
Heavy duty traffic such as car parks, ramps industrial warehouses, logistical centers,...etc.
Mechanical and chemical exposure applications.
Laboratories, hospitals, food and Beverage industries.
Freezer rooms and applications where thermal shock resistance is required.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map
Home
About us
news and events
Contact
DOWNLOAD SECTION
REFERENCES
Copyright ©2015-2016 Saudi Vetonit Co. Ltd. All Rights Reserved.