Flooring & Coatings Systems
Vetotop EL395

Self-smoothening Novaloc epoxy based floor topping from 0.8 to 2mm thickness

Floor topping for a variety of industrial applications such as: production chemical plants, secondary containment areas, dairies, bottling plants, breweries, pharma plants, etc.
Wet working areas subject to chemical spillage.
Clean rooms and laboratories.
Fast Download
Technical Data Sheet
download (*.pdf 0.24Mb)
Technical Information
Product Description

Vetotop EL395 is a two component high performance self-smoothening Novolac epoxy flooring system that flows in a honey like manner to self-smoothen to a perfect level. Once cured, the product has excellent abrasion and chemical resistance. Vetotop EL395 provides an attractive hard wearing and easily cleanable floor finish. Its use on floors will enhance lighting in the environment due to the product reflective properties.


Superior glossy and leveled finish.

High abrasion and impact resistance. Ease of application.

High chemical resistance.

Low maintenance costs.

Hygienic, impervious and easily cleanable.

High bond, stronger than concrete cohesive strength.

Fast Curing.


Compiliance Standard

BS EN476:2009 as class 1 in flame spread.

Packaging & Coverage



Pack Size

Theoretical Coverage

Vetotop EL395

15 Liter Kits

1m2/ liter @1mm

Vetoprime EP491

4 Liter Kits

8m2 / liter

Stated consumptions data are for general guidance. Actual consumption depends on the nature of substrate, method of application and wastage.

Shelf life & Storage

Original sealed kits of Vetotop EL395 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.

Application Information
Instructions for use


Vetoprime EP491 is the recommended primer for Vetotop EL395.

After priming, the surface must be free of pin-holes. Vetoprime EP491 should be mixed in the proportions supplied. Add the entire contents of the Hardener Can to the Base Can.

When thoroughly mixed, preferably using a slow speed mixer, the primer should be applied in a thin, continuous film using rollers or stiff brushes. Work the primer well into the surface of the concrete taking care to avoid ponding or over application. The primer should be left to achieve a tack-free condition before applying the top coat.


Vetotop EL395 is supplied in two pre-weighed packs (base and hardener), which are ready for immediate on-site use. Part mixing of these components is not acceptable and will affect both performance and appearance of the finished floor. Mixing should be carried out using either a forced action mixer, or a heavy duty mobile mixer fitted with a jiffy type mixing paddle.

All such equipment should be of a type and capacity approved by Saveto. The components should be mixed in a suitable sized mixing vessel. Stir the base and hardener components individually, then empty them into the mixing vessel scrapping the edges. Mix for further 3 minutes until a completely homogeneous material is obtained.


Ensure there are sufficient labor and materials to make the mixing and subsequent application process a continuous one for any given, independent floor area. Once mixed, use the material within its specific pot life. Pour the mixed material onto the prepared and primed substrate. Spread the material to the required thickness by using a notched trowel or a gauged 

spreader; take care not to overwork the resin, spread slowly and evenly. Immediately after laying, roll the material by using a spiked nylon roller, to remove the slight trowel marks, and to assist air release. Rolling should be carried out using ‘Back and Forth’ technique along the same path. An overlap of 50% with adjacent paths is recommended. Prior the product setting, further light rolling may be required to remove surface imperfections, or for subsequent release of trapped air.

Floor Joints

New floor surface should follow all the existing expansion or movement joints. Joint  sealant  and  joint geometry should be compatible with the floor type used, intended exposure conditions and likely movement characteristics of the substrate. Consult local Saveto office for more details.


Tools and equipment should be cleaned with Vetonit Solvent XX400 immediately after use. Hardened material can only be removed mechanically.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.

Laitance and weak surface layer shall be removed using mechanical methods such as grinding or blasting in order to provide a sound well profiled surface. All necessary repairs should be made prior to application by using epoxy mortar from Vetorep ER range.

New concrete floors shall be at  least  28  days  old  with moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).

Additional Information
Health & Sefety

Vetotop EL395, Vetoprime EP491, and Vetonit Solvent XX400 should not come into contact with skin and eyes or be swallowed. Ensure adequate ventilation and avoid inhalation of vapors. Some people are sensitive to resins, hardeners and solvents. Wear suitable protective   clothing,   gloves,   and   eye   protection.   If working in confined areas, suitable respiratory protective equipment must be used.

The use of barrier cream provides additional skin protection.

In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately. Do not induce vomiting.

Vetonit Solvent XX400 is flammable. Keep away from sources of ignition. No Smoking. In the event of fire

extinguish with CO₂ or foam.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any lia-

bility either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us.

Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notifi- cation. Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetodeck UD

Polyurethane based heavy duty, waterproof and UV resistant car park decking system

Vetotop CL530

Premixed 2 to 10 mm thick cementitious self leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed.

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed.

Vetotop EC198

Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating

view more
Featured Product
Vetonit PAB500

Saveto plaster accessories - angle beads


Help the formation of corners and abutments which are resistant to chips, cracks and impact damage.
Protect corners & edges
Giving better shape for the corners and edges.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map