Non-toxic solvent free epoxy waterproof wall, floor & tank coating
Vetoproof EC720 is a two component non-toxic high performance solvent free epoxy coating system that adheres perfectly to concrete and metal substrates. Once cured, the product has excellent abrasion and chemical resistance. Vetoproof EC720 provides an attractive hard wearing and easily cleanable hygienic coating. Its use on floors, walls and tanks will enhance lighting in the environment due to the product light reflective properties.
Vetoproof EC720 supplied in 4 Liter Kit. Coverage - 5 m²/liter @ 200 microns
Vetoprime EP491 supplied in 4 Liter Kit. Coverage - 7-10 m²/liter
Original sealed bag of Vetoproof EC720 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.
Priming is not normally required provided the substrate is sound, prepared and good quality non porous concrete. However, if concrete surface is porous, or w/c ratio is >0.5 it is recommended to use Vetoprime EP491. Vetoprime EP491 should be mixed in the proportions supplied. Add the entire contents of the hardener can to the base can. When thoroughly mixed, preferably using a slow speed mixer, the primer should be applied in a thin, continuous film using rollers or stiff brushes. Work the primer well into the surface of the concrete taking care to avoid ponding or over application. The primer should be left to achieve a tack-free condition before applying the top coat.
In a separate mixing vessel, use a slow speed mixer to mix the base, hardener for 3 minutes. Mix these components in the quantities supplied taking care to ensure all containers are scraped clean. Do not add solvent thinners at any time. The first coat of Vetoproof EC720 should be laid using a short haired lamb wool roller, or squeegee to achieve a continuous coating. Ensure that loose hairs on the roller are removed before use. A minimum film thickness of 200 microns per coat should be applied for flooring system (this can be increased where specifi cations demand). The top coat can be applied in the same manner within 8 to 24 hours of the application of the top coat.
The first coat of Vetoproof EC720 should be laid using a short haired lamb wool roller or airless spray equipment to achieve a continuous coating. Ensure that loose hairs on the roller are removed before use. A minimum film thickness of 200 microns per coat should be applied. Apply the second coat in a perpendicular manner to the first coat ensuring a minimum dry film thickness of 200 microns. It is recommended to use a different color for each coat to ensure complete coverage.
Tools and equipment should be cleaned with Vetonit Solvent XX400 immediately after use.
All surfaces should be dry and free from contamination such as oil, grease, loose particles, decayed matter, moss algal growth, laitence, and all traces of mould release oils and curing compounds. This is best achieved by lightly grit-blasting the surface. Where moss, algae or similar growths have occurred, treatment with a proprietary biocide should be carried out after the grit-blasting process. Spalled and deeply disintegrated concrete should be removed to sound concrete and repaired with a Saveto repair system. Minor irregularities leveling and pin hole filling can be achieved using Vetorep ER350.
Vetoproof EC720, Vetoprime EP491 and Vetonit Solvent XX400 through all paragraphs. should not come into contact with skin and eyes or be swallowed. Ensure adequate ventilation and avoid inhalation of vapors. Some people are sensitive to resins, hardeners and solvents. Wear suitable protective clothing, gloves, and eye protection. If working in confined areas, suitable respiratory protective equipment must be used. The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medial advice. If swallowed, seek medical attention immediately - Do not induce vomiting. Vetonit Solvent XX400 through all paragraphs. is flammable. Keep away from sources of ignition. No Smoking. In the event of fire extinguish with CO2 or foam.
Vetoproof EC720 and Vetoprime EP491 are nonflammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Single component acrylic waterproofing membrane
Single component elastomeric crack-bridging cementitious waterproof membrane
Single component ultra flexible acrylic waterproofing membrane
Polymer modified water resistant cementitious top coat
Single component penetrating waterproofing system for concrete
Silica hardwearing aggregates to be used in conjunction of Saveto Anti-slip flooring system