Sprayable premixed plaster
Plaster Cement Perlite is composed of a hydraulic cement, Perlite and selected aggregates with special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce cohesive mix. Plaster Cement Perlite is a high quality product and provides as underlayment on various facets of the projects.
Plaster Cement Perlite supplied in 25 Kg Bag or Bulk. Consumption - 1 to 1.2 Kg / m2 / mm.
Original sealed container of Plaster Cement Perlite has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.
Plaster Cement Perlite is designed to be used at thicknesses between 10 - 30 mm in a layered application. The product can be applied on block walls without the need to use a scratch coat as long as the substrate is properly irrigated prior to application. In cases of fairfaced concrete; a scratch coat is needed to insure mechanical keying and enhanced bonding.
Add to the mixing container 7-8 liters of water for each 25 Kg bag of Plaster Cement Perlite. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
Do not add water to the mix once the mixed mortar start to harden.
Smooth Concrete Surfaces
Apply Spatter Dash SB prior to the application of Plaster Cement Perlite.
Plaster Cement Perlite can be applied in a single or multiple layers on rough surfaces. On smooth surfaces it should be applied subsequent to the application of a spatter-dash coat. Rod or level to a uniform thickness immediately then follow smoothing the material to the desired appearance. For multiple layers allow the plaster to partially dry (60-120 minutes depending on weather). Apply second coat at thickness as described above to a desired appearance. After the surface appears stiff but still moist, follow the smoothing the material to achieve a desired appearance.
Plaster Cement Perlite is best cured by spraying water on its surface every 8-12 hrs for a minimum of 3 days. During hot & dry conditions allow curing for minimum of 5 days. It will help to obtain high mechanical strengths and minimize the risk of surface cracks.
Substrate should be sound, clean, free from loose material, grease, laitence, dirt curing compound, or any other substance that might impair the quality of bond with the substrate. Prior to Plaster Cement Perlite Application, damp the entire surfaces with clean potable water. The substrate should be a neutralized surface at the time of Plaster Cement Perlite application.
Make sure the substrate is suitable for the application of Plaster Cement Perlite, in case of doubt, try on sample area to assess its suitability. Do not apply the product under direct rain, extreme wind, and at temperatures below +5ºC or above +45ºC. Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically.
Plaster Cement Perlite is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap and water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.
Plaster Cement Perlite is non-flammable.
For further information, please refer to material safety data sheet.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Light weight gypsum perlite plaster
Manual Applied Premixed Plaster
Sprayable Cemenitious Premixed Plastering/Rendering Material
Polymer modified water resistant adhesive for fixing pool, fountain & water tank tiles.