Premixed 2 to 10 mm thick cementitious self leveling underlayment
Vetotop CL530 is a single component cementitious floor self leveling underlayment composed of hydraulic binders, selected aggregates and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, once mixed it will form a cohesive self smoothening honey-like flowing mortar that is applied in thicknesses between 2 and 10 mm giving a super flat finish ready to receive final floor coverings including tiles, carpets, resinous flooring systems, parquet, ...etc.
Vetotop CL530 supplied in 25 Kg / Bag. Yield - 1.5 - 1.8 Kg/m²/mm.
Original sealed bag of Vetotop CL530 has a shelf life of 6 months provided it is stored clear of ground in a dry and shaded place below 35ºC.
For single bag mixing add to the mixing container 4.75 - 5.13 liters of water for each 25 Kg bag of Vetotop CL530. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3 - 4 minutes, until a uniform, lump-free consistency is achieved.
Try to minimize the water addition to get higher strength. Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when homogeneous mix is achieved.
Vetotop CL530 can be applied using screw type pump with pumping rate of 25-50 liters/min and length of hose 40-50 LM. and control the water dosage to achieve the required flow.
After placing onto the primed surface, apply by trowel or pin screed. Rake to the Vetotop CL530 spreads and adjust itself to a level floor.
For small areas Vetotop CL530 can be applied manually. Use a suitable spike roll to remove entrapped air if there is any.
The product is a self-curing product and should be left undisturbed for 3 to 5 days prior to use of subsequent toppings.
The applied product should be protected from environmental agents such as wind, direct sunlight, dirt and dust exposure to ensure smooth leveled hard surfaces for at least the first 24 hrs.
The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Larger areas can be divided with wooden battens to control the pumping volume and determine the layer thickness to be applied.
Priming the substrate is vital, use Vetoprime PB433 diluted with potable water (ratio of 1:1.5), or use Vetoprime PB435 without dilution. Mix thoroughly and spray or brush onto the floor without pooling. Before applying Vetotop CL530, it’s important to leave the primer between 30-60 minutes to fully dry. In case of doubt, check the primer dryness by adding drops of water on top of the primer substrate, it should not absorb the water drops.
Vetotop CL530 is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.
Vetotop CL530 is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Polyurethane based heavy duty, waterproof and UV resistant car park decking system
Premixed 10 to 30 mm thick cementitious screed.
Premixed 30 to 100 mm thick cementitious screed.
Water-Based Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating
Solvent based high performance, self priming, thin epoxy topping
Two-component trafficable, jet fuel resistant heavy duty pitch-polysulphide sealant.