(Formerly known as Vetomortar CHR)
High strength structural repair mortar
Vetorep CR520 is a single component polymer modified fibered cementitious structural repair mortar that is ready to use and only requires the addition of water on site. Once mixed the products becomes a thixotropic mortar that is hand applied for the repair of demanding structural repair while being compatible with host concrete. Vetorep CR520 is composed of a blend of hydraulic cements, carefully selected and graded aggregates, fibers and special additives to give it its unique properties.
- Vetorep CR520 supplied in 25 Kg Bag. Consumption - 14 Liters Yield.
- Vetobond AB432 supplied in 4 Liter Can. Consumption - 6-8 m2 / Liter.
- Vetoprime CP43supplied in 2Kg Kit. Consumption - 1.2 m2 @ 1mm
Note: Vetorep CR521 repair area should not exceed 2.5 m2 in single application.
Original sealed kits of Vetorep CR520 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded temperature controlled place <35ºC.
Application area shall not exceed 2.5 m2 using Vetorep CR520, if such conditions exits use Vetorep CR521. Theuse of Vetorep CR520 in a single layer shall conform to:
Vertical application up to 75 mm.
Overhead concrete repair up to 50 mm.
All damaged and weak concrete should be cut back to reach sound concrete and/or to a minimum depth of at least 10 mm. Corroded steel reinforcement should be grit blasted to remove all rust traces. In case of signifi cant loss in the steel reinforcement cross section, the steel should be replaced. Remove all concrete form around exposed steel reinforcements by 25 mm thickness. The perimeters of the repair area should be saw cut to a minimum depth of 10 mm. The prepared area should be cleaned thoroughly by brush and/or compressed air.
To accept Vetorep CR520, all grit blasted steel reinforcements should be primed within 2 to 4 hours with one or two coats of corrosion inhabitor for steel reinforcement Vetoprime CP437.
Areas to be repaired with Vetorep CR520 should be soaked with clean water before applying the repair mortar. All excess water should be removed prior to applying one coat of acrylic bonding agent Vetobond AB432.
Vetobond AB432 should be allowed to become tacky before applying the repair mortar
To ensure proper mixing, a mechanically powered mixer or drill fi tted with suitable paddle should be used. 2.8 to 3 liters of clean water should be added to a clean container.
The powder is then added slowly to the water while mixing continuously with low speed mixer/drill (400 - 600 rpm). Mixing time should be continued for 5 minutes until uniform consistency is obtained.
Vetorep CR520 Contains reins which may cause sensitization by skin contact. Avoid contact with skin and eyes and inhalation of vapor. Wear suitable protective clothing, gloves and eye/face protection. Barrier creams provide additional skin protection. Should accidental skin contact occur, remove immediately with a resin removing cream, followed by soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed seek medical attention immediately. Do not induce vomiting.
Vetorep CR520 is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Epoxy resin twin cartridge anchoring grout
Polyester injection and anchoring grout
Water based concrete curing compound
Multi-Purpose Acrylic Resin Curing Compound
Multipurpose universal cementitious non-shrink grout
Polymer modified hygienic cementitious fine non sanded tile grout for hospitals & clinics