Water resistant internal use premix smooth cement coating
Vetonit Finish WR is a cement based smooth finishing coat composed of hydraulic binders, selected aggregates and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce easily workable material. Vetonit Finish WR is a high quality product for multipurpose use. Vetonit Finish WR can be applied in thickness from 1 mm to 3 mm.
Finish WR supplied in 25 Kg Bag
Consumption: 1.0 - 1.2 Kg/m²/1mm Thickness.
Original sealed bags of Finish WR has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.
Internal Block Walls & Rough Surfaces
For manual application add to the mixing container 9.5-11.0 litres of water for each 25 Kg bag of Vetonit Finish WR. For Spray machine application use 11.0-13.0 litres of water for each 25 kg bag. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved. Allow the mixed material to stand for about 10 minutes and remix briefly with no further water to be added.
Smooth Concrete Surfaces & Ceilings
Add 0.5 litres of Vetonit Bond 2 to the mixing water and adjust the water requirement accordingly for each 25 kg bag. Follow same mixing procedure as described above.
Mixed material can be used within 3 hours. Do not add water to the mix once the mixed mortar start to harden.
Vetonit Finish WR should be applied in layers to achieve desired thickness of 1-3 mm.
Various grades of finish textures can be obtained by selecting appropriate spray machine nozzle sizes.
Allow the installed application to remain undisturbed for at least 48 hours.
Vetonit Finish WR is best cured by spraying water on the surface of applied material every 12 hrs for minimum 3 days. In case of using Vetonit Finish WR as underlayment layer to receive a final finishing system, you can add 1 liter of Vetonit Bond 2 / Bag to improve curing process. This will help in achieving uniform colour, minimize risk of surface cracks and high mechanical strengths.
All tools should be cleaned immediately after finishing by water. Hardened materials can be cleaned mechanically.
The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Prior to Finish WR application, wet the entire surfaces with clean potable water and surface should look damp at the time of Finish WR application.
Finish WR is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application.
Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.
Vetonit Finish WR is non-flammable.
For further information, please refer to material safety data sheet.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
High quality premixed surface crack filler
Water resistant external use premix smooth cement coating
Premium quality premixed compound for gypsum board joints
Water resistant high quality premixed putty
Weather Resistant Premix Cement Coating for External Use
Advanced modified cementitious light weight, thermal insulating masonry mortar