UAE
Bahrain Egypt Jordan Saudi Arabia
EN
EN
Contact news and events About us Home
PRODUCT RANGE
SYSTEM
Selector REFERENCES DOWNLOAD SECTION
Concrete Grouts, Repairs, & Enhancements
Vetogrout GA514

Cable Grout Additive

Uses
Post tensioned bridge deck ducts.
Pre-stressed structural element cables ducts.
Slip form silo tendon ducts.
Fast Download
Technical Data Sheet
download (*.pdf 0.20Mb)
Method of Statement
download (*.pdf 0.24Mb)
MSDS
download (*.pdf 0.83Mb)
Technical Information
Product Description

Vetogrout GA514 is a preblended powder admixture containing expansive agents which impart controlled expansion in the plastic state whilst minimising water demand. The material is designed to allow uniform mixing, and eliminates unwanted segregation and bleeding.

Advantages
  • Plastic state shrinkage compensation.
  • High early strength promotion.
  • Increased concrete durability and permeability reduction.
  • Compatibility with ordinary portland cement.
Compiliance Standard

- BS EN 445
- BS EN 196

Packaging & Coverage

Vetogrout GA514 is supplied in 24 kg Bag

Shelf Life & Storage

Original sealed bag of Vetogrout GA514 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place.

Application Information
Instructions for use

Mixing
For best results a mechanically powered grout mixer should be used. Do not use a colloidal impeller mixer, if sands/aggregates are being used. To enable the grouting operation to be carried out continuously, it is essential that sufficient mixing capacity and labour are available. The use of a grout holding tank with provision to gently agitate the grout may be required.
33 to 38 litres of clean water (depending on nature of cement) and 100 kg of cement are required to be added per 6 kg bag to achieve the correct consistency.
The water should be accurately measured into the mixer. The total contents of the Vetogrout GA514 bag should be slowly added with the cement and continuous mixing should take place for 5 minutes. This will ensure that the grout has a smooth even consistency.

Placing
Place Vetogrout GA514 mix within 20 minutes of mixing in annular gaps of up to 60 mm thick. A screw feeding pump such as PFT ZP3 booster pump or equivalent can be used.

Curing
Use standard curing practices as per ACI recomendation to cure any exposed surfaces of the placed mix bu use of a curing compound such as Vetocure XT425.

Cleaning
Tools and equipment can be cleaned with fresh water. Hardened material needs to be removed mechanically.

 

Surface Preparation

Preparation


Several hours prior to grouting, the area should be flooded with fresh water. Immediately before grouting takes place any free water should be removed.
All cable ducts must be thoroughly cleaned. Those ducts formed without metal sheaths should be flushed with water after which all surplus water must be removed. Cable anchorages should be sealed before the duct grouting is carried out.

Design Consideration

Vetogrout GA514 os tested using 50 mm cubes. The mixture design shall be based on the following to achieve required results:

  • 6 Kg of Vetogrout GA514.
  • 33 to 38 Liters of clean water.
  • 100 Kg of Ordinary portland cement.
Limitation

Sampling Procedure

  • All sampling procedures for Vetogrout GA514 are to be conducted within the confines of a temperature controlled laboratory. The reactive agents within Vetogrout GA514 do not permit site sampling and transport. The procedure for sampling is to be as follows:
    A full and unopened bag of Vetogrout GA514 to be selected from the batch allocated for site use and despatched to the testing laboratory.
  • The Vetogrout GA514 shall be mixed in the laboratory following the instructions listed on the product data sheet.
  • All sampling shall be conducted using 50 mm cube moulds, any other size is not permissible.
  • When mixed, the Vetogrout GA514 shall be poured into 50 mm cube moulds, treated with release agent, in two lifts of 25 mm each with a 60 second interval between pours. The Vetogrout GA514 shall not be tamped, but gentle tapping of the cube mould is permitted to promote the release of air.
  • Fill three 50 mm cube moulds with the Vetogrout GA514 for each curing time interval specified. Mould filling should be completed within 15 minutes of the end of the mixing cycle. The filled moulds should be stacked three high on top of each other to provide conditions of restraint. The top mould should be restrained either with a weighted metal plate or an empty cube mould.
  • The cubes should be stored at a 20°C + 2°C temperature for 24 hours in the laboratory. After 24 hours the cubes are to be de-moulded and placed in a water curing tank maintained at a 20°C + 2°C temperature. The cubes are then to be cured in accordance with standard curing practices.
  • Cubes are to be crushed in calibrated compression testing apparatus with a rate of loading not exceeding 0.2 - 0.4 N/mm2 per-second. Types of cube fracture are to be recorded. Three cubes are to be crushed for each curing time interval specified. Results are to be calculated and issued as an average.
Additional Information
Health & Sefety

Vetogrout GA514 is alkaline and should not come into contact with skin and eyes. Avoid inhalation of dust during mixing. Gloves, goggles and dust mask should be worn. If contact with skin occurs, wash with water. Splashes to eyes should be washed immediately with plenty of clean water and medical advice sought. Vetogrout GA514 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346

Epoxy resin twin cartridge anchoring grout

vetoanchor PG347

Polyester injection and anchoring grout

Vetocure XT425

Water based concrete curing compound

Vetocure XT426

Multi-Purpose Acrylic Resin Curing Compound

Vetogrout CG510

Multipurpose universal cementitious non-shrink grout

view more
Featured Product
Vetotop EC498

Solvent free high performance, high build epoxy flooring system

Uses
Floor coating for a variety of industrial applications such as: production assembly areas, workshops, dairies, bottling plants, breweries, pharma plants, kitchens, showrooms, etc.
Aircraft hangers, anti-slip floors, ramps & high traffic.
Wet working areas subject to chemical spillage.
Vehicle production factories and parks.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map
Home
About us
news and events
Contact
DOWNLOAD SECTION
REFERENCES
Copyright ©2015-2016 Saudi Vetonit Co. Ltd. All Rights Reserved.