Premixed 20 to 100 mm thick conventional cementitious mortar.
Vetotop CX534 is a single component cementitious backing mortar composed of hydraulic binders, silica sand and selected aggregates. It is supplied in bulk as a dry pumpable powder ready to use on site, once mixed it will form a trowellable mortar that is applied in thicknesses between 20 and 100 mm.
Factory controlled pre-blend ensures consistent high quality.
Suitable for Middle East harsh weather conditions.
Easy application enabling high productivity through pumps and horizontal mixers.
Easy to break and refurbish backing to install additional piping and mechanical fittings.
Excellent workability.
Replaces conventional site batched mortars.
Applied on horizontal damp compacted sand and cementitious substrates while providing good adhesion.
Contains special additive that reduces friction and prolongs lifespan of equipment.
- ASTM C 150
- ASTM C 207
- ASTM C 136
Vetotop CX534 is supplied in 50kg bag or Bulk, Yield: 0.5 - 0.6 Ltr / Kg
Vetotop CX534 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.
Application
Vetotop CX534 can be applied in a single layer to the desired thickness using HM 24 machine. Rod or screed to a uniform thickness immediately then follow with installation of the tiles. To insure better coverage increase the thickness and firmly press on the tile squeezing the excess out. For better adhesion you can use Vetobond PB434 product call technical engineer for advice.
Curing
Vetotop CX534 is best cured by spraying water on the surfaces of the tiles before grouting for 2-3 days. During hot & dry conditions allow curing for minimum of 5 days.
Cleaning
Clean tools with water promptly before material hardens. Hardened material can be mechanically removed.
Surface Preparation
Substrate should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc. Prior to Vetotop CX534 Application, wet the entire surfaces with clean potable water and surface should look damp at the time of application.
Mixing
For manual mixing, add to the mixing container 9-10.5 liters of water to each 50kg bag of Vetotop CX534. Add the powder to the water and mix with mechanical mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
For application using HM 24 Mixing & pumping machine, the water flow rate is 300-500 Lit/hour. Mixed material should be used within 1 hour.
Re-tempering is allowed between 60 and 90 minutes for one time only.
Smooth Concrete Surfaces
Apply Vetobond PB433 or Vetobond EB430 as a primer coat or prepare the horizontal substrate by chopping or chiseling.
Design Criteria
Vetotop CX534 is designed for application for pumpingmachine (HM 24) and contains special shrinkage control additive and provides good adhesion. The product is available in grey and white color and can be applied in thickness from 2 to 10 cm.
Vetotop CX534 is highly alkaline therefore avoid direct contact with eyes or skin. Vetobond BR434 is latex emulsion. It is recommended to use protective gloves and goggles during application.
Any skin contact should be washed with plenty amount of water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.
Vetotop CX534 is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Polyurethane based heavy duty, waterproof and UV resistant car park decking system
Premixed 2 to 10 mm thick cementitious self leveling underlayment
Premixed 10 to 30 mm thick cementitious screed.
Premixed 30 to 100 mm thick cementitious screed.
Water-Based Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating
Multipurpose universal cementitious non-shrink grout