Elastomeric, pigmented acrylic, anti-chloride ion and carbonation protective and decorative coating for concrete and masonry
Vetotop AC441 is a single component penetrating silane-siloxane primer and a single component elastomeric pigmented coating, both ready for immediate site use. Vetoprime AP443 is supplied as a clear liquid and is based on an acrylic resin and a silane-siloxane dissolved in a penetrating organic carrier. Vetoprime AP443 is reactive and capable of producing a chemically-bound hydrophobic barrier, thus inhibiting the passage of water and water-borne contaminants. Vetotop AC441 is a crack-accommodating, water based protective coating based on a special acrylic polymer, providing outstanding elongation and recovery, resistance to aggressive elements, UV light and rain.
Vetotop AC441 is supplied in 20 Kg Pail with coverage of 4 m2/ kg @200 mic WFT
Vetoprime AP443 is supplied in 5 Liter Can, with consumption of 0.4 Liter/m2
Original sealed buckets of Vetotop AC441 and Vetoprime AP443 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.
Vetotop AC441 should generally be applied in two coats to achieve a total dry film thickness of not less than 200 microns in order to accommodate substrate cracking up to 2 mm and cyclic movement up to 0.3 mm. It is possible to achieve the total dry film thickness in one coat however, this depends on the substrate type and the finish required. Trials are recommended prior to full application to ensure the finish meets the clients requirements. To achieve the correct protective properties, Vetotop AC441 must be applied on to the substrate at the coverage rates recommended.
Vetoprime AP443 should be applied first. It should be applied in one or more coats until the recommended application rate of 0.4 litre per square metre has been achieved. This is best accomplished by using portable spray equipment. A uniform surface appearance (sheen) should be achieved.
The primer should be allowed to dry for a minimum of two hours (at 20°C) before overcoated with Vetotop AC441.
In order to obtain the protective properties of the Vetotop AC411 system, it is important that the correct rates of application and overcoating times are observed.
Vetotop AC441 should be applied in two coats. First coat can be thinned with clean water depending on the substrate. Recoat time for second coat is two hours. If necessary, a third coat can be applied to achieve a hiding power.
It is important that no gaps or ‘raw edges’ appear in the finished coating. Special care should be taken to provide an unbroken coating at external corners and similar exposed protrusions.
Vetotop AC441 may be applied by the use of suitable brushes, rollers or airless spray equipment.
Vetotop AC441 should be removed from tools and equipment with clean water immediately after use.
All surfaces should be dry and free from any contamination and all traces of mould release oils and curing compounds. This is best achieved by lightly grit-blasting the surface. Where moss, algae or similar growths have occurred, treatment with a proprietary biocide should be carried out after the grit-blasting process.
Where application over existing sound coatings is required, trials should be conducted to ensure compatibility and retention of the bond between the underlying coating and the substrate. It is essential to produce an unbroken coating of Vetotop AC441. Surfaces containing blow-holes or areas of pitting should first be filled using Vetorep CR523 , a cementitious fairing coat. Rougher substrates can be levelled using a cementitious product from Saveto Concrete Repair Range.
Vetotop AC441 should not come in contact with the skin and eyes, or be swallowed. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water.
In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice.
If swallowed, seek medical attention immediately, do not induce vomiting.
Vetotop AC441 is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Polyurethane based heavy duty, waterproof and UV resistant car park decking system
Premixed 2 to 10 mm thick cementitious self leveling underlayment
Premixed 10 to 30 mm thick cementitious screed.
Premixed 30 to 100 mm thick cementitious screed.
Water-Based Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating
(Formerly known as Vetomortar CHR)
High strength structural repair mortar