Universal cementitious grout for large thickness repair & grouting
Vetogrout CG519 is a single component polymer modified fibered cementitious structural and non-shrink micro-concrete that is ready to use and only requires the addition of water on site. Once mixed the products becomes a self compacting micro-concrete that is applied by pouring into prepared form-work for the repair of demanding structural repair while being compatible with host concrete. Vetogrout CG519 is composed of a blend of hydraulic cements, carefully selected and graded aggregates, fibers and special additives to give it its unique properties.
Vetogrout CG519 is supplied in 50kg Bags, Consumption: 23.0 Liters Yield
Vetobond AB432 is supplied in 4 liters Can, Consumption: 6-8 m2 / Liter
Vetoprime EP310 is supplied in 1 liter Can, Consumption: 7.5 m2 / Liter
Vetobond EB430 is supplied in 1 liter Can, Consumption: 8 m2 / Liter
Original sealed kits of Vetogrout CG519 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded temperature controlled place <35ºC.
Vetogrout CG519 repair area should not exceed 2.5 m2 in single application.
For best results a mechanically powered grout mixer should be used. When quantities up to 50 kg are used, a slow speed drill fitted with a high shear mixer is suitable. Larger quantities will require a high shear vane mixer. Do not use a colloidal impeller mixer.
To enable the grouting operation to be carried out continuously, it essential that sufficient mixing capacity and labor are available. The use of a grout holding tank with provision to gently agitate the grout may be required.
Water to be added is 11-13% by weight of the grout and should be accurately measured into the mixer. The total contents of the Vetogrout CG519 bag should be slowly added and continuous mixing should take place for 5 minutes. This will ensure that the grout has a smooth even consistency.
At 25ºC place the grout within 20 minutes of mixing to gain full benefit of the expansion process.
Vetogrout CG519 can be placed in thicknesses up to 100 mm in a single pour when used as an under-plate grout. For thicker sections it is necessary to fill out Vetogrout CG519 with well-graded silt free aggregate to minimize heat build-up. Typically a 10 mm aggregate is suitable. Any bolt pockets must be grouted prior to grouting between the substrate and the base plate.
Continuous grout flow is essential. Sufficient grout must be prepared before starting. The time taken to pour a batch must be regulated to the time to prepare the next one.
On completion of the grouting operation, exposed areas should be thoroughly cured. This should be done by the use of Vetocure XT425 water based curing compound and wrapping with polyethylene sheets.
Vetogrout CG519 should be removed from tools and equipment with clean water immediately after use. Cured material can be removed mechanically.
The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.Wet the substrate to achieve a saturated and surface dry condition prior to application of Vetogrout CG510.
Erect hopper system and form-work, make sure that the shuttering is watertight by use of a polyurethane sealant such as Vetoflex PU780 or a rubber gasket seal. This step is important to insure no cement paste and water leak from the shuttering. Contact you Saveto’s local representative for more technical information and Saveto’s grouting detailed method statement and CAD details.
It is essential that the base plate is clean and free from oil, grease or scale. Air pressure relief holes should be provided to allow venting of any isolated high spots.
If leveling shims are used and are to be removed after the grout has hardened, they should be treated with a thin layer of grease.
Unrestrained Surface Area
Generally the gap width between the perimeter form-work and the plate edge should not exceed 150 mm on the pouring side and 50 mm on the opposite side. It is advisable where practical to have no gap at the flank sides.
Vetogrout CG519 Contains reins which may cause sensitization by skin contact. Avoid contact with skin and eyes and inhalation of vapor. Wear suitable protective clothing, gloves and eye/face protection. Barrier creams provide additional skin protection. Should accidental skin contact occur, remove immediately with a resin removing cream, followed by soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed seek medical attention immediately. Do not induce vomiting.
Vetogrout CG519 is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Epoxy resin twin cartridge anchoring grout
Polyester injection and anchoring grout
Water based concrete curing compound
Multi-Purpose Acrylic Resin Curing Compound
Multipurpose universal cementitious non-shrink grout
Specialty polymer modified cementitious adhesive for glass blocks and glass mosaic tiles.