Flooring & Coatings Systems
Vetotop UC373

Line Marking Polyurethane Coating for Traffic

As a line marking paint with Vetotop range of products or car park deck coating systems.
General epoxy and polyurethane coated decks
Car park flooring
Concrete surface in factories, warehouses and car parks
Playground and sport flooring
Kerb stones and stair, treads
Technical Information
Product Description

Vetotop UC373 is a specially formulated fast drying line marking paint that can be applied in one coat for marking lines on concrete, epoxy or polyurethane surfaces. Vetotop UC373 paint is based on Polyester-Polyurethane

  • Suitable for exterior and interior applications
  • Quick drying
  • Excellent resistance against water, oil, alkalis and hydrocarbon fuels
  • Good adhesion to concrete, epoxy and polyurethane coatings
  • Durable with excellent abrasion resistance
  • Good reflection properties when mixed with glass beads
Compliance Standard
  • DIN 53457
  • BS EN476:2009 as class 1 in flame spread.
Packaging & Coverage

Vetotop UC373 is supplied in  1 & 4 Liter, Coverage: 5-6 m2 / Liter

Stated consumptions data are for general guidance. Actual consumption depends on the nature of substrate, method of application and wastage.
In case of use of antislip aggregates, the consumption values for the top coat will be reduced by 15 - 20%.

Shelf Life & Storage

Original sealed bag of Vetotop UC373 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.
Keep the product in tightly closed containers stored in dry covered place, at a temperature not less that +5°C and not more than +35°C. Under these conditions, the product will have a shelf life of 12 months.

5 Standard Colors: 1023 3020 5017 6024 9016
Application Information
Instructions for use

Mix the contents of the container thoroughly before application.

Vetotop UC373 can be applied with brush, roller or airless spray gun. It may be needed to dilute the product with 5 to 10% Vetonit Solvent XX300, If airless spray gun is used. The nozzle tip of the gun should be from 4-6 mm. Apply the paint with a pressure of 30-40 psi.
Apply Vetotop UC373 at a rate of 5m2/Liter (200 microns wet). If another coat is needed to build up the thickness, then apply the second coat after the first one is totally dry.
For the light reflection, proper glass beads with size

Clean tools with Vetonit Solvent XX300 promptly before material hardens. Cured material must be mechanically removed.

Surface Preparation

The surface should be sound, clean, dry and free from loose material, laitance, dirt, oil, grease or any  other contaminants. If needed, wash the surface with detergent and then with clean water. Allow to dry completely before application. Do not use solvent to clean the surface before applying the product.


Do not apply the paint during rainy or stormy weather or when humidity is greater than 80%

Additional Information
Health & Safety

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.
In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.
If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetodeck UD

Polyurethane based heavy duty, waterproof and UV resistant car park decking system

Vetotop CL530

Premixed 2 to 10 mm thick cementitious self leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed.

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed.

Vetotop EC198

Water-Based Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating

view more
Featured Product
Vetotouch TYROLEAN

Exterior decorative textured render

Special Stenciled and textured finishes designed for interior/exterior application.
As a finish coat for of EIFS / ETICS systems.
On plastered, fairfaced concrete surfaces.
On block walls and pre-cast panels.
3-6 mm thickness.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map