UAE
Bahrain Egypt Jordan Saudi Arabia
EN
EN
Contact news and events About us Home
PRODUCT RANGE
SYSTEM
Selector REFERENCES DOWNLOAD SECTION
Wall & Facade Systems
Vetotouch Sealer

Decorative protective sealer for cementitious finishes
(formally Known as Vetotop AC444)

 

Uses
Sealing of Vetotouch range of cementitious decorative products.
Semi Solid finish protection and sealing of cementitious facades.
Fast Download
Technical Data Sheet
download (*.pdf 0.31Mb)
Technical Information
Product Description

Vetotouch Sealer is an environmentally friendly polymeric pore sealer for Vetotouch range of decorative products. The product seals the surface finish to protect against contaminants and water ingress.

Advantages
  • Easily applied by roll or airless-spray.
  • Protects against contaminants and water ingress.
  • Designed to work with cementitious finishes and Vetotouch range of products.
  • Cost effective, suitable for use in MENA region weathering conditions.
Packaging & Coverage

Vetotouch Sealer is supplied in 20 liters pail. Theoretical coverage: 3 - 6 m2/ liter/ coat

 

Shelf Life & Storage

Original sealed containers of Vetotouch Sealer has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.

Colors
Colored Liquid
Application Information
Instructions for use

Design Criteria

Designed to work with Vetotouch range of cementitious decorative products. The application is designed to a 2 - 3 coats at a rate of 3 to 6 m2 per liter per coat to achieve best results and closing the substrate surface. The coverage rate may decrease or increase depending on the porosity of the substrate and its texture.
Note: You can dilute by water up to 15% if required.

Application

Vetotouch Sealer should be applied as a continuous flood coat using either a soft brush or low pressure spray equipment at the correct coverage rate. For best performance apply a flood of 2 - 3 coats at rate 3 - 6 m2 per liter per coat

Cleaning

Equipment  and tools can be cleaned using clean water immediately after use. Shall residual material exist or harden, mechanical means such as wire brush would be required to remove residue. 

 

Surface Preparation

Surface must be sound and thoroughly cleaned by compressed air before Vetotouch Sealer is applied. 

Additional Information
Health & Sefety

Vetotouch Sealer should not come into contact with skin and eyes or be swallowed. Avoid inhalation of vapor and spray. Use only in well ventilated areas. In case of insufficient ventilation wear suitable respiratory protection.
Wear suitable protective clothing, gloves and eye/face protection. Barrier creams provide additional skin protection.
Should accidental skin contact occur, remove immediately with a suitable skin cleanser followed by washing with soap and water.
In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
If swallowed, seek medical attention immediately - do not induce vomiting.
Refer to Material Safety Data Sheet for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Cool Plaster

Advanced modified cementitious thermal insulating plaster

 

Cool Mortar

Advanced modified cementitious light weight, thermal insulating masonry mortar 

 

Vetotherm FLEX

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm ULTRA

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm Plaster

Advanced Modified Cementitious Thermal Insulating Plaster

view more
Featured Product
Vetotop UC372

High performance, matt finish chemical, scratch & UV resistant polyurethane floor & wall coating

Uses
long term protection of car parks and floors in factories, warehouses, laboratories, loading decks ramps, showers, kitchens, dairies, breweries.
UV Resistant top coat over flooring systems including concrete, epoxies, aromatic elastic polyurethanes,...etc.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map
Home
About us
news and events
Contact
DOWNLOAD SECTION
REFERENCES
Copyright ©2015-2016 Saudi Vetonit Co. Ltd. All Rights Reserved.