Self-smoothening anti-static, conductive epoxy based floor topping from 1 - 2mm thickness
Vetotop EL383 is a two component solvent free, conductive epoxy flooring system which consists of an insulating primer, self-adhesive conductive tape, conductive primer and a conductive top layer with excellent abrasion and chemical resistance. Anti-static floors are required to control static electricity such as in hospital operating rooms, cleaning rooms and hazardous & chemical environments.
Vetotop EL383 supplied in 7 liter kit. Yield 4.7 m2/kit @ 15mm thickness.
Original sealed kit of Vetotop EL383 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 25ºC.
Original sealed kit of Vetotop EL383 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 25ºC.
The substrate is to be primed by Vetoprime EP491prior to the application of Vetotop EL393.
Vetoprime EP491 should be mixed in the proportions supplied. Add the entire contents of the hardener can to the base can. When thoroughly mixed, preferably using a slow speed mixer, the primer should be applied in a thin, continuous film using rollers or stiff brushes.
Work the primer well into the surface of the concrete taking care to avoid ponding or over application. The primer should be left to achieve a tack-free condition before applying Vetoprime EP381.
After the drying of Vetoprime EP491, fix self-adhesive conductive tape over the primed surface.
Mix Vetoprime EP381 as per above mixing instructions of Vetoprime EP491. Apply Vetoprime EP381 at a rate of 8-10m2/liter in a single coat.
Consult Saveto technical representative for proper installation procedure as per the established norms and guidelines for optimum connectivity and results.
Vetotop EL383 is supplied in two pre-weighed packs (base and hardener) which are ready for immediate on-site use. Part mixing of these components is not acceptable and will affect both performance and appearance of the finished floor. Mixing should be carried out using either a forced action mixer; or a heavy duty mobile mixer fitted with a jiffy type mixing paddle. All such equipment should be of a type and
capacity approved by Saveto. The components should be mixed in a suitably sized mixing vessel. Stir the base and hardener components individually then empty them into the mixing vessel scrapping the edges and mix for 2 minutes. The contents of the filler pack should be slowly added and mixing carried out for a further 3 minutes until a completely homogeneous material is obtained.
Ensure that there are sufficient labor and materials to make the mixing and subsequent application process a continuous one for any given, independent floor area. Once mixed, the material must be used within its specified pot life. The material should be poured onto the prepared and primed substrate as soon as mixing is complete. It should be spread to a thickness 1.5-2mm using a notched trowel or a gauged spreader; with care taken not to overwork the resin, spreading evenly and slowly. Immediately after laying, the material should be rolled, using a spiked nylon roller, to remove slight trowel marks, and to assist air release. The rolling should be carried out using a ‘back and forth’ technique along the same path. An overlap of 50% with adjacent paths is recommended. Further light rolling may be required to remove surface imperfections, or for subsequent release of trapped air, but should be prior to the setting of the product.
Vetoprime EP491, Vetoprime EP381, and Vetotop EL383 should be removed from tools and equipment with Vetonit Solvent XX400 immediately after use. Hardened material can only be removed mechanically.
The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc. Laitance and weak surface layer shall be removed using mechanical methods such as grinding or blasting in order to provide a sound well profiled surface.
Materials should be pre-conditioned at 25°C to reduce the possibility of flash and slow setting.
All necessary repairs should be made prior to application by using epoxy mortar from Vetorep ER range.
New concrete floors shall be at least 28 days old with moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).
Vetotop EL383, Vetoprime EP491,Vetoprime EP381 and Vetonit Solvent XX400 should not come into contact with skin and eyes or be swallowed. Ensure adequate ventilation and avoid inhalation of vapors. Some people are sensitive to resins, hardeners and solvents. Wear suitable protective clothing, gloves, and eye protection. If working in confined areas, suitable respiratory protective equipment must be used.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any lia-
bility either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us.
Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notifi- cation. Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Polyurethane based heavy duty, waterproof and UV resistant car park decking system
Premixed 2 to 10 mm thick cementitious self leveling underlayment
Premixed 10 to 30 mm thick cementitious screed.
Premixed 30 to 100 mm thick cementitious screed.
Water-Based Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating
High performance crack-accommodating elastomeric acrylic protective and decorative coating for concrete and masonry