UV resistant, gloss finish easy to clean solvent-based polyurethane wall coating
Vetotop UC375 is a clear two component, solvent based UV resistant urethane sealer. It is used as UV resistant sealer over masonry, concrete, gypsum and various decorative finishes. The material has excellent adhesion to minimally profiled concrete. Vetotop UC375 is UV stable for use in exterior applications, cures rapidly and the sealed system is ideal for all weather exposure. When used as a finish coat, Vetotop UC375 gives a hard, glossy surface that offers excellent stain resistance and easy cleanability. Vetotop UC375 is supplied in a pack size of 4 liters kit consist of Resin & Hardener.
Product |
Pack Size |
Vetotop UC375 |
4 Liter Kits |
Vetoseal XX777-25 |
5 Liter Jerrycan |
Product |
Theoretical Coverage |
Vetotop UC375 |
2.5 - 5.0 m2 / Liter / coat |
Vetoseal XX777-25 |
4 -10 m2 / Liter / coat |
Stated consumptions data are for general guidance. Actual consumption depends on the nature of substrate, method of application and wastage.
Substrate Priming
Vetotop UC375 can be applied directly to most sound surfaces. However, if the surface is highly absorbent or powdery in nature; then priming is recommended using Vetoseal XX777-25.
Mixing Vetotop UC375
In a separate plastic mixing vessel, use a slow speed mixer to mix the base, hardener for 3 minutes. Mix these components in the quantities supplied taking care to ensure all containers are scraped clean. Do not add solvent thinners or water at any time.
Let the mixed material remain in covered container for 1-2 minute prior to use.
Application
Apply Vetotop UC375 by roller or brush to the surface. The application should be at a rate of 2.5-5.0 m2 /liter per coat.
Application should not be carried out when humidity exceeds 85% or drops below 5%, or when the surface temperature to be coated is less than 3°C above the dew point.
Do not apply in direct sunlight or when ambient temperatures are above 40°C or below 7°C.
Cleaning
Tools and equipment should be cleaned with Saveto Solvent XX300.
The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Laitance and weak surface layer shall be removed using mechanical methods such as grinding in order to provide a sound well profiled surface. All necessary repairs should be made prior to application.
New concrete shall be at least 28 days old with moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).
Vetotop UC375 is irritant and harmful therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advice.
In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. If swallowed, seek medical attention immediately - Do not induce vomiting.
Vetotop UC375 and Vetoseal XX777-25 are flammable. Keep away from open flames. Refer to product(s) MSDS for further information.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us.
Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notifi- cation. Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Polyurethane based heavy duty, waterproof and UV resistant car park decking system
Premixed 2 to 10 mm thick cementitious self leveling underlayment
Premixed 10 to 30 mm thick cementitious screed.
Premixed 30 to 100 mm thick cementitious screed.
Water-Based Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating
Sprayable Cemenitious Premixed Plastering/Rendering Material