Primers and Ancillary
Vetoprime CP436

Corrosion inhibitor for steel reinforcement accepting cementitious repair or concrete.

Uses
Ideally designed as corrosion protection for steel reinforcement in the concrete repair systems
Fast Download
Technical Data Sheet
download (*.pdf 0.22Mb)
Technical Information
Product Description

Vetoprime CP436 is a two component polymer modified cementitious primer designed to enhance the bond between the Concrete Repair range of repair mortars and existing reinforced steel. Vetoprime CP436 is also designed to protect the steel reinforcement by providing a highly alkaline passivating layer around the reinforcement and by the use of migrating corrosion inhibitor technology, which minimizes further corrosion to surrounding steel reinforcement.

Advantages
  • Two component, easy to use.
  • High bond strength to concrete and steel.
  • Good physical properties and mechanical strength.
  • Polymer modified system with low VOC.
  • Protection of steel through migrating Corrosion
  • Inhibitor technology.
  • Good resistance to water and chloride
  • Safe and environment friendly product.

 

Packaging & Coverage

Vetoprime CP436

2 kg Kit 1.18m2/2kg Kit @ 1mm

4 kg Kit 2.35m2/4kg Kit @ 1mm

Shelf Life & Storage

Original sealed containers  of Vetoprime  CP436  have a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 35ºC.

Application Information
Instructions for use

Mixing

Mix Vetoprime CP436 by slowly adding the powder component to the liquid component. Mix thoroughly for about 2 minutes until obtaining a smooth, and even consistency.

Application As Reinforcement Primer

Apply by using a brush two coats of Vetoprime CP436 in a 1mm thickness approximately. Allow each coat to reach the initial setting prior to the application of the second coat.

Cleaning

Clean all tools and equipment immediately after use with water.

Surface Preparation

It is essential to apply Vetoprime CP436 to a sound, clean, and dry surface in order to achieve maximum bond strength between substrate and coating/repair products.

All rust and scale should be removed from any exposed steel   reinforcement   by   grit   blasting    techniques or equivalent approved methods to a bright steel condition

Additional Information
Health & Safety

Vetoprime CP436 should not come into contact with skin and eyes or be swallowed. Avoid inhalation of vapor and spray. Use only in well-ventilated areas. In case of insufficient ventilation wear suitable respiratory protection. Wear suitable protective clothing, gloves, and eye/face protection. Barrier creams provide additional skin protection. Should accidental skin contact occur, remove immediately with a suitable skin cleanser followed by washing  with  soap  and  water. In case of contact with eyes, rinse immediately with plenty of water, and seek medical advice. If swallowed, seek medical attention immediately - do not induce vomiting.

Vetoprime CP436 is non-flammable.

Refer to Material Safety Data Sheet for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any

liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us.

Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Saveto Bond 2

Multipurpose low viscosity bonding agent & admixture

Vetobond PB436

Polymeric soil stabilizer

Vetobond PB434

Polymeric bonding agent, waterproof mix enhancer & primer

Vetobond PB433

Versatile resin adhesive, cement modifier, bonding agent & sealer

Vetobond EB430

Solvent free epoxy bonding agent to bond old to new concrete

view more
Featured Product
Vetotop CX534

Premixed 20 to 100 mm thick conventional cementitious mortar.

Uses
Cost effective cavity filling in non-structural areas.
Non-structural backing mortar.
Filling around underfloor heating installations and mechanical fittings.
As a bedding mortar for granite and marble.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map