Sprayable premixed cement based plaster and render
PlasterMix-S PLS222 is a cement based plastering material composed of hydraulic binders (OPC), selected graded aggregates, fi bers, and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only the addition of clean water to produce cohesive mortar. PlasterMix-S PLS222 is specially designed for application by spray machine and contains special shrinkage control additive and provides good adhesion with uniform color surface. PlasterMix-S PLS222 can be applied at thicknesses ranging from 10 mm to 20 mm.
Fast mixing application using spray machine
Applied directly on AAC and normal block walls without the need for key coat.
Factory controlled pre-blend ensures consistent high quality.
Requires only addition of water on-site at the time of usage.
Improved workability & curing.
Easy application with uniform work flow enables high productivity & superior finishing.
Strong adhesion on variety of substrates.
Internal & external applications.
Shrinkages control reduces surface cracks.
Suitable for humid & dry conditions.
Suitable for vertical & ceiling surfaces.
Free from Asbestos, very low VOC
BS EN 13914-1,2
ASTM C 926
ASTM C 897
ASTM C 150 type I, EN 197-1
BS EN 998-1
PlasterMix-S PLS222 - 5 kg - 1.6-2.0 sqm @ 15 mm depending on application & wastages
Original sealed container of PlasterMix-S PLS222 has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place.
Original sealed container of PlasterMix-S PLS222 has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place.
Mixing
Add to the mixing container 6.5 to 8 liters of water for each 50 Kg bag of Plaster. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
For application using Saveto plastering machine, the water fl ow rate is 300 - 400 Lit / hour. Monitor condition of rotor stator as it affects the water ratio.
Mixed material should be used within 90 min. Do not add water to the mix once the mixed mortar start to harden.
Smooth Concrete Surfaces/Thick Plaster:
Apply Spatter Dash at 4 to 6 mm thickness and allow to cure sufficiently prior to the application of PlasterMix-S PLS222.
Application
PlasterMix-S PLS222 can be applied in a single or multiple layers on rough surfaces. On smooth concrete surfaces (and thick paster > 20 mm.) it should
be applied subsequent to the application of a spatterdash coat.
Rod or level to a uniform thickness immediately then follow smoothing the material to the desired appearance.
For multiple layers allow the first plaster layer (15 mm.) to cure for 2-3 days. Apply next layer at thickness not more than 15 mm.
After the surface appears stiff but still moist, follow the smoothing the material to achieve a desired appearance.
For plastering ceilings, it is recommended to use vetonit Render.
Curing
PlasterMix-S PLS222 is best cured by spraying water
on its surface every 8-12 hrs for a minimum of 3 days.
During hot & dry conditions allow curing for minimum
of 7 days. It will help to obtain high mechanical
strengths and minimize the risk of surface cracks.
Substrate should be sound, clean, free from loose material, grease, laitence, dirt, curing compound, or any other substance that might impair the quality of bond with the substrate.
Prior to Plaster Application, wet the entire surfaces with clean potable water. The substrate should be saturated surface dry at the time of Plaster application.
Make sure the substrate is suitable for the application of plaster, in case of doubt, try on sample area to assess its suitability.
Do not apply the product under direct rain, extreme wind, and at temperatures below +5ºC or above +45ºC.
Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically.
PlasterMix-S PLS222 is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application.
Any skin contact should be washed with soap and water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.
PlasterMix-S PLS222 is non-fl ammable. and noncombustible (Class A1). For further information, please refer to material safety data sheet.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specifi cation, recommendation or information given by us.
Saveto has the right to change any of the specifi cations mentioned in the Technical data sheets upon its discretion without prior notifi cation. Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
High quality light weight premixed acoustic plaster
High quality gypsum plaster.
Sprayable premixed plaster
Light weight gypsum perlite plaster
Sprayable premixed cement based plaster and render
High performance aliphatic acrylic protective & decorative coating for concrete and masonry