Plasters & Masonry
Spatter Dash-MC SDM212

Weather resistant premixed cementitious key coat for dense concrete (GGBS, MS, Fly Ash)

 Internal & external rush coat for plasters.
 On block walls, fairfaced concrete and precast panels prior to plastering application.
 Plaster bond enhancer and mechanical key on horizontal, vertical and overhead application.
 on normal concrete and concrete modified with ggbs, micro silica, fly ash.
Technical Information
Product Description

Spatter Dash-MC cement based key coat composed of Ordinary Portland Cement, selected sand aggregates and high performance additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce easily spray-able mortar. Spatter Dash-MC is a high quality product for multipurpose applications and contains special bonding agent.
Substrates compatible with: smooth concrete (normal and modifi ed), masonry walls (CMU, AAC, Bricks, Calcium Silicate)


 Factory controlled pre-blend ensures consistent high quality.
 Requires only addition of water on-site at the time of usage.
 Manual or tyroleane machine application or by hawk & trowel techniques.
 Superior workability.
 Excellent adhesion on variety of substrates.
 Internal & external applications.
 Suitable for humid & dry conditions.
 Suitable for vertical & ceiling surfaces.
 compatible with normal concrete and normal concrete block walls
 Free from Asbestos or Asbestos Containing Materials.
 Free from VOC

Compliance Standard

 BS EN 998-1
 ASTM C-926
 Cement type: ASTM C-150, type1, BS EN 197-1

Packaging & Coverage

Spatter Dash-MC - 50 Kg Bag 1.4-1.6 Kg / m2/ mm thickness~210 m²/Ton @ 4 mm thickness

Shelf Life & Storage

Original sealed container of Spatter Dash-MC has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place.

Grey Granular Powder
Shelf life & Storage

Original sealed container of Spatter Dash-MC has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place.

Application Information
Instructions for use

Add to the mixing container 8.0 - 10.0 liters of water for each 50 Kg bag of Spatter Dash-MC. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fi tted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when homogeneous mix is achieved.
Mixed material shall be used within maximum one hour of mixing. Dont use set material and do not retemper after setting.

Spatter Dash-MC is preferably applied in a single coat application to achieved desired rough thickness of 4-6mm.
Apply mixed material using mechanical spray or manual spatter tyroleane machine or hawk & trowel technique.
Cover 100% of surface area to be plastered.
Allow the installed application to remain undisturbedfor at least 48 hours.

Spatter Dash-MC is best cured by spraying water on the surfaces of applied materials every 8 hrs for minimum of 2 days. During hot & dry conditions allow curing for minimum of 5 days. It will help to obtain high mechanical strengths and minimize the risk of surface cracks.

Surface Preparation

Substrate should be sound, clean, free from loose material, grease, laitence, dirt, curing compounds, or any other substance that might impair the quality of bond with the substrate.
Prior to Spatter Dash-MC Application, damp the entire surfaces with clean potable water. The substrate should be neutralized surface at the time of Spatter Dash-MC application.


Make sure the substrate is suitable for the application of Spatter Dash-MC, in case of doubt, try on sample area to assess its suitability.
Do not apply the product under direct rain, extreme wind, and at temperatures below +5ºC or above +45ºC.
Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically.

Additional Information
Health & Safety

Spatter Dash-MC is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap and water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.
Spatter Dash-MC is non-fl ammable. For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specifi cation, recommendation or information given by us.
Saveto has the right to change any of the specifi cations mentioned in the Technical data sheets upon its discretion without prior notifi cation. Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Acoustic Plaster

High quality light weight premixed acoustic plaster

Gypsum Plaster

High quality gypsum plaster.

Plaster Cement Perlite

Sprayable premixed plaster

Plaster Gypsum PERLITE

Light weight gypsum perlite plaster

PlasterMix-S PLS221

Sprayable premixed cement based plaster and render

view more
Featured Product
Vetotop CL530

Premixed 2 to 10 mm thick cementitious self leveling underlayment

Leveling of concrete slabs prior to application of final floor coverings such as tiles and resinous systems.
As a substrate for vinyl tiles, parquet, carpet and floor coverings that require super-flat substrates.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map