UAE
Bahrain Egypt Jordan Saudi Arabia
EN
EN
Contact news and events About us Home
PRODUCT RANGE
SYSTEM
Selector REFERENCES DOWNLOAD SECTION
Concrete Grouts, Repairs, & Enhancements
Vetorel XT420

Water based mold and form-work release agent

Uses
Vetorel XT420 is used for the treatment of wooden and metal form work or molds prior to the casting of concrete to facilitate form stripping
Minimizing concrete surface blemishes and pinholes
Fast Download
Technical Data Sheet
download (*.pdf 0.16Mb)
Method of Statement
download (*.pdf 0.23Mb)
MSDS
download (*.pdf 0.15Mb)
Technical Information
Product Description

Vetorel XT420 is a single component milky liquid composed of synthetic oils, special emulsifying agents and varied additives with high anti-adhesion properties towards concrete. Vetorel XT420 provides the plywood surface with a water repellent film preventing concrete from adhering to the form work resulting with a smooth, stainless concrete surface.

Advantages
  • Factory controlled single component easy to use
  • Water based, environment friendly product
  • Odorless and non flammable
  • Produces neat concrete surfaces by letting the air & water bubbles rise freely during vibration
  • Minimize surface staining even with white cement based concrete
  • Adheres to all wooden or plywood form surfaces, as well as to synthetic or steel forms
  • Ensure easy release and cleanability while extending usable life of shuttering
Packaging & Coverage

Vetorel XT420 supplied in 20 & 200 Ltr. Theoretical Coverage: 7 - 20 m2/Ltr.

Stated consumptions data are for general guidance. Actual consumption depends on the nature of substrate, method of application and wastage.

Shelf Life & Storage

Shelf Life & Storage

Original sealed container of Vetorel XT420 and has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 35ºC.

Application Information
Instructions for use

Application

Vetorel XT420 is supplied in pails or drums ready to use at site without a need to premix operation. It can be applied by brush, roller or spraying machine.

Apply Vetorel XT420 on plywood or steel shutter before the first casting. After every use of form-work, the shutter should be re-coated lightly with Vetorel XT420.

Do not over apply Vetorel XT420 on the form-work. Excessive material should be allowed to drain before using the form-work.

Apply the product with a brush or preferably with a sprayer. For best results, it is advisable to apply Vetorel XT420 at least two hours before using the shutter.

Consult Saveto technical department for any additional information.

Cleaning

Clean tools with water promptly before material hardens. Hardened material can be mechanically removed.

Surface Preparation

All form-work, shutter surfaces must be cleaned from deposits of rust, concrete, oil or other materials. The product is ready to use without any dilution.

Limitation

- Do not mix the product with water as it will lose its properties.

- Do not mix with other materials.

- Do not apply the product at temperature less than +5ºC.

- Vetorel XT420 should be checked for its suitability when concrete is steam cured. Also carry out prior test for its suitability when gypsum or colored mixes are being used.

- For further information contact our technical department.

Additional Information
Health & Sefety

Vetorel XT420 is harmful therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advise, if irritation persist.

Vetorel XT420 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346

Epoxy resin twin cartridge anchoring grout

vetoanchor PG347

Polyester injection and anchoring grout

Vetocure XT425

Water based concrete curing compound

Vetocure XT426

Multi-Purpose Acrylic Resin Curing Compound

Vetogrout CG510

Multipurpose universal cementitious non-shrink grout

view more
Featured Product
Vetonit Putty WR

Water resistant high quality premixed putty

Uses
Leveling of minor surface undulations
Applied externally & internally in wet to dry conditions onto the walls & ceilings such as bathrooms & kitchens
On concrete and plastered surfaces that are smooth and also precast concrete surfaces
Suitable for use over surfaces that are plastered with Saveto products and on gypsum boards
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map
Home
About us
news and events
Contact
DOWNLOAD SECTION
REFERENCES
Copyright ©2015-2016 Saudi Vetonit Co. Ltd. All Rights Reserved.