Concrete Grouts, Repairs, & Enhancements
Vetorel XT421

Chemical mold and form-work release agent

Vetorel XT421 is used for the treatment of wooden and metal form work or molds prior to the casting of concrete to facilitate form stripping
Minimizing concrete surface blemishes and pinholes
Technical Information
Product Description

Vetorel XT421 is a single component, low viscosity pale straw colored liquid composed of synthetic mineral oils and special varied additives that performs in a superior manner to standard oil based mold release agents. Vetorel XT421 provides the plywood surface with a water repellent film preventing concrete from adhering to the form work resulting with a smooth, stainless concrete surface.

  • Factory controlled single component easy to use
  • Stainless fair-faced concrete finish
  • Ensures easy release reducing damage to molds and form-work
  • Produces neat concrete surfaces by letting the air & water bubbles rise freely during vibration
  • Performs all wooden or plywood form surfaces, GRC as well as to synthetic or steel forms
  • Extend usable life of shuttering
Compliance Standard

Concrete Society Category 5 chemical mold release agent.

Packaging & Coverage

Vetorel XT421 supplied in 20 & 200 Ltr. Theoretical Coverage: 7 - 30 m2/Ltr.

Shelf Life & Storage

Original sealed container of Vetorel XT421 and has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 35ºC.

Application Information
Instructions for use


Vetorel XT421 is supplied in pails or drums ready to use at site without a need to premix operation. It can be applied by brush, roller or spraying machine.

Apply Vetorel XT421 on plywood or steel shutter before the first casting. After every use of form-work, the shutter should be recoated lightly with Vetorel XT421

Do not over apply Vetorel XT421 on the form-work. Excessive material should be allowed to drain before using the form-work.

Apply the product with a brush or preferably with a sprayer. For best results, it is advisable to apply Vetorel XT421 at least two hours before using the shutter.

Consult Saveto technical department for any additional information.

Surface Preparation

All molds, shutter surfaces must be cleaned from deposits of rust, concrete, oil or other materials. The product is ready to use without any dilution.

Additional Information
Health & Safety

Vetorel XT421 contains hydrocarbon oils and should be treated as potentially harmful as there is a possible risk of irreversible effects in contact with skin. Vetorel XT421 should not be swallowed or allowed to come into contact with skin and eyes. Avoid inhalation of vapors and ensure adequate ventilation.

Wear suitable gloves and eye/face protection. Should accidental skin contact occur, remove immediately with soap and water - do not use solvent.

In case of contact with eyes rinse immediately with plenty of water and seek medical advice, if swallowed seek medical attention immediately - do not induce vomiting.

For further information consult the Material Safety Data sheet available for this product.


Vetorel XT421 has a shelf flash point, so the flammability risk is low. Do not expose to naked flames or other sources of ignition.

Flash point: above 60ºC.

Cleaning and disposal

Spillages of Vetorel XT421 should be absorbed onto sand, earth or vermiculite and transferred to suitable containers. Contaminated areas will become slippery.

The disposal of excess or waste material should be carried out in accordance with local legislation under the guidance of the local waste regulatory authority.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346

Epoxy resin twin cartridge anchoring grout

vetoanchor PG347

Polyester injection and anchoring grout

Vetocure XT425

Water based concrete curing compound

Vetocure XT426

Multi-Purpose Acrylic Resin Curing Compound

Vetogrout CG510

Multipurpose universal cementitious non-shrink grout

view more
Featured Product
Vetotop AC441

Elastomeric, pigmented acrylic, anti-chloride ion and carbonation protective and decorative coating for concrete and masonry

To protect atmospherically exposed reinforced concrete structures from attack by acid gases, chloride ions, oxygen and water.
Suitable to protect all cementitious substrates and masonry including those in coastal environments.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map