Renders & Finishes
Vetonit Render RND310

Water & Weather resistant Leveling and Repairing premixed render for concrete walls/ceilings

Uses
Internal & external leveling plaster & render
Applied on both vertical and over-head surfaces
Plastering to a thickness of 15 mm in a single application.
Excellent for plastering ceilings and concrete walls in one coat.
Leveling of Precast walls and Ceilings.
Fast Download
Technical Data Sheet
download (*.pdf 0.10Mb)
Technical Information
Product Description

Vetonit Render RND310 is a cement based mortar composed of hydraulic binders (OPC), polymer powders, selected sand aggregates and special additives. It is supplied as a dry powder in pre- weighed bags ready to use on site, which requires only addition of clean water to produce cohesive mortar. Vetonit Render is a high quality product contains shrinkage control additive. It is ideal for patch repair and leveling application.

Vetonit Render RND310 is available in Grey, White and vetonit colors.

Advantages
  • Applied directly on walls and ceilings without the need for key coat.
  • Factory controlled pre-blend ensures consistent high quality.
  • Requires only addition of water on-site at the time of usage.
  • Suitable for ME harsh weather conditions.
  • Easy application with uniform work flow enables high productivity & superior finishing.
  • Strong adhesion on variety of substrates: cast in concrete, precast, masnry walls, ceilings.
  • Internal & external applications.
  • Shrinkage control reduces surface cracks.
  • Suitable for wet to dry conditions.
  • Free from Asbestos, very low VOC
Compliance Standard
  • BS EN 998-1, EN 13914
  • ASTM C926
  • ASTM C-150 type I
  • ASTM C-897
Packaging & Coverage

vetonit Render RND310 stored in 50 Kg Bag.

Coverage: ~ 6 m2@ 5 mm. thickness

Stated coverage data are for general guidance and it may vary depending on nature of substrate and wastages.

Shelf Life & Storage

Original sealed bag of Render RND310 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place.

Colors
Grey, White and Colored Powder
Application Information
Instructions for use

Mixing
For manual mixing, add to the mixing container 8 -10 litres of water for each 50 Kg bag of Vetonit Render. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fi tted with a suitable paddle for 3 - 4 minutes, until a uniform, lumpfree consistency is achieved.
Leave the mixed material to stand for 10 min and briefly remix without addition of water.
Manual mixing is allowed for small batch quantities and mix for approx. 1 - 2 min or when homogenous mix is achieved.

Application
Vetonit Render can be applied in a single layer upto 15 mm or multi-layers on rough or smooth surfaces to desired thickness. For multi-layer application, fi rst layer should not exceed 15 mm. Apply mixed material using spray machine or hawk & trowel technique, pushing fi rst layer hard against the substrate. Rod or screed to uniform thickness. Immediately then follow smoothing the surface, if single layer repair.
For second layer allow the fi rst layer to cure for 24 hours. Apply second coat as described above to desired total thickness not exceeding 30 mm. Each layer shall not exceed 10 mm. and must be allowed for 24 hours curing.

After curing, surface can be coated with vetonit Finish WR or WR EG, vetotouch decorative products, or with paint.

Curing
Render is best cured by spraying water on the surfaces of applied materials every 12 hrs for minimum of 3 days. During hot & dry conditions allow curing for minimum of 5 days. It will help to obtain high mechanical strengths and minimize the risk of surface cracks.

Cleaning
Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically only.

Surface Preparation

Substrate should be sound, clean free from loose material, grease, laitance, dirt curing  ompound, etc. Prior to the application, wet the entire surfaces with clean potable water and surface should look damp at the time of application.

Limitation

Do not mix with any additives or products unless recommended by Saveto.
Make sure the substrate is suitable for patching, repair application. In case of doubt, try on sample area to assess its suitability. Do not apply the product at temperature less than +5ºC. During summer season the working area must be covered to prevent ill-effects from direct sun and also excessive air-draught during initial curing stage.

Additional Information
Health & Safety

Vetonit Render RND310 is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.

Vetonit Render RND310 is non-flammable. For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetonit Crack Filler

High quality premixed surface crack filler

Vetonit FINISH WR

Water resistant internal use premix smooth cement coating

Vetonit FINISH WR EG

Water resistant external use premix smooth cement coating

Vetonit Gypsum Joint Compound

Premium quality premixed compound for gypsum board joints

Vetonit Putty WR

Water resistant high quality premixed putty

view more
Featured Product
Vetotop US364

High performance solvent free polyurethane screed for heavy duty applications 

Uses
Heavy duty traffic such as car parks, ramps industrial warehouses, logistical centers,...etc.
Mechanical and chemical exposure applications.
Laboratories, hospitals, food and Beverage industries.
Freezer rooms and applications where thermal shock resistance is required.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map